Related Manuals for Excalibur Water Systems 1.5 “ HIGH CAPACITY SIMPLEX WATER SOFTENER
Summary of Contents for Excalibur Water Systems 1.5 “ HIGH CAPACITY SIMPLEX WATER SOFTENER
- Page 1 1.5 “ HIGH CAPACITY SIMPLEX WATER SOFTENER INSTALLATION AND OPERATIONS MANUAL www.excaliburwater.com Barrie, ON L4N 4Y8...
- Page 2 Water Softener Introduction: Please read Excalibur Water Systems Water Softener manual carefully before starting the Water Softener installation. The Water Softener manual contains detailed information about your new Water Softener, including the Water Softener Installation, Settings, Start up and Operation. The Excalibur Water Softener has been designed and engineered to provide soft conditioned water for many years, when the Water Softener is properly installed and operated.
- Page 3 Water Softener Components: Media Tank; The Water Softener media tank features Excalibur fiberglass wound high impact Water Softener media tank. The media Water Softener tank contains quartz underbedding, single point distributor, Excalibur high capacity durable synthetic Water Softener resin which meets Excalibur Water System’s rigid specifications.
- Page 4 6 Cycle Control Valve; The reliable Excalibur Water Softener control valve provides direct flow of water during regeneration. The Water Softener control valve is constructed with durable corrosion resistant materials, epoxy coated, the piston operated design assures positive, accurate positioning even in turbidity water problem water supplies. The six cycle Water Softener control valve sequence of operation is as follows: 1.
- Page 5 replacing and carrying out the calcium and magnesium. This restores the Water Softener capacity. Then the Water Softener goes into slow rinse cycle which is when all the brine has been drawn from the Water Softener brine tank. An eliminator built into the brine safety valve, prevents air from being drawn into the water softener tank.
- Page 6 Hardness: Water hardness is a term which describes the materials dissolved in the water which forms scale in pipes and water heaters and causes graying of laundry, just to name a few. The Water Softener will perform and will remove all water hardness to zero. Iron: Iron through not always visible when water is drawn can cause reddish staining of fixtures and clothing and even a dry metallic taste...
- Page 7 basement is 50psi (345kpa) it will be about 40psi (276kpa) on the second floor or a reduction of about 5psi (34kpa) for every 10 feet of elevation. Location: The location of the Water Softener should be selected on the basis of the following factors.
- Page 8 Warning; Always connect a ground wire; an improperly grounded Water Softener could cause injury from electrical shock. Drain Requirements; The Water Softener has an open free flowing drain capable of carrying the maximum drain flow rate may be used. This may take the form of a floor drain, utility sink or stand pipe.
- Page 9 Water Softener Button Operation and Function: Scrolls to the Water Softener next display Pressing Water Softener regen button once and releasing will schedule a Water Softener regeneration at the preset Water Softener delayed regeneration time. Pressing again and releasing will cancel the Water Softener regeneration.
- Page 10 Water Softener Regeneration and Error Screens; Water Softener Regeneration Screen: Water Softener control valve displays the time remaining in the current cycle. Pressing the Water Softener regen button advances to the next Water Softener cycle. Water Softener Error Screen; The Water Softener alternated Err and error code every 3 seconds.
- Page 11 Water Softener User Displays When the water softener is operating, one of the five water softener displays may be shown. Pressing the water softener next button will alternate between the displays shown below. Water Softener User 1 Typical water softener user display. If water softener volume is selected in configuration settings step 3cs.
- Page 12 Setting Water Softener Time of Day Push the water softener next button until Time of Day screen is displayed. Press the water softener up arrow and hold until the water softener set indicator is displayed and the hour flashes. Press the water softener up and down arrows until the water softener displays the correct hour.
- Page 13 Water softener installer display settings The water softener has one of three settings on what was selected in configuration settings step 3cs. Volume (gallons) selected in configuration settings step 3cs. Step 1I – To enter water softener display press the water softener next and up buttons on the water softener simultaneously for 5 seconds and release.
Need help?
Do you have a question about the 1.5 “ HIGH CAPACITY SIMPLEX WATER SOFTENER and is the answer not in the manual?
Questions and answers