Page 1
Troy-Bilt® is a registered trademark of MTD and is used under license to Briggs & Stratton Power Products. Troy-Bilt® es una marca registrada registrada de MTD y se usa abajo licencia a Briggs & Stratton Power Products. BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON, WISCONSIN, U.S.A.
Section 1: Safety Rules WARNING DANGER Fuel and its vapors are extremely flammable and Running engine gives off carbon monoxide, an explosive. odorless, colorless, poison gas. Fire or explosion can cause severe burns or Some chemicals or detergents may be harmful if death.
Page 4
Section 1: Safety Rules WARNING CAUTION Excessively high or low operating speeds increase risk Running engines produce heat and hot exhaust of injury and damage to pressure washer. gases. Temperature of muffler and nearby areas can reach or exceed 150°F (65°C). •...
Features and Controls Section KNOW YOUR PRESSURE WASHER Read this owner’s manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Pump equipped with Air Filter Automatic Cool Down System...
Assembly Section ASSEMBLY PREPARING PRESSURE WASHER FOR USE IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer. If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the Remove Pressure Washer from pressure washer helpline at 1-888-611-6708.
Section 3: Assembly Secure tray to handle with self tapping screws using a Pinch chemical hose and slide it into metal clip as #2 phillips screwdriver. Ensure screws are tight but not shown in Figure 5. crushing plastic accessory tray. Figure 5 —...
Section 3: Assembly Connect Hose and Water Supply to Before connecting garden hose to water inlet, inspect inlet screen (Figure 10). Clean screen if it contains Pump debris, replace if damaged. DO NOT RUN PRESSURE IMPORTANT: To avoid pump damage, you must WASHER IF SCREEN IS DAMAGED.
Operation Section Check to make sure there are no kinks, cuts, or Place colored quick connect spray tips in slots on damage to high pressure hose. holder that’s attached to nozzle extension (Figure 12). Provide a proper water supply at an adequate flow. Figure 12 —...
Section 4: Operation How to Use Accessory Tray Figure 15 — Spray Tip Spray Patterns The unit is equipped with an accessory tray with places to Low Pressure store your nozzle extension and slots to hold the cleaning solution bottle and the detergent siphoning filter. There are also two hooks at the ends of the handle to hold your spray gun and high pressure hose.
Section 4: Operation Cleaning and Applying Chemical prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking). IMPORTANT: Use soaps designed specifically for IMPORTANT: You must flush the chemical injection pressure washers. Household detergents could damage system after each use by placing the filter into a bucket of pump.
Maintenance Section GENERAL MAINTENANCE WARNING RECOMMENDATIONS The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and The pressure washer warranty does not cover items that have possible amputation. been subjected to operator abuse or negligence.
Section 5: Maintenance Detach spray gun and nozzle extension from high Nozzle Maintenance pressure hose. Detach nozzle extension from spray A pulsing sensation felt while squeezing the spray gun gun and remove o-ring and screen from nozzle trigger may be caused by excessive pump pressure. The extension.
Section 5: Maintenance An O–Ring Maintenance Kit is provided with your pressure ENGINE MAINTENANCE washer which includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet See the engine owner’s manual for instructions on how to provided in the kit to service your unit’s o-rings.
Section Storage PREPARING THE UNIT NOTE: PumpSaver is available as an optional accessory. It is not included with the pressure washer. Contact the nearest FOR STORAGE authorized service center to purchase PumpSaver. CAUTION Water should not remain in the unit for long periods of time.
Section Troubleshooting TROUBLESHOOTING Problem Cause Correction Low pressure spray tip installed. Replace spray tip with high pressure spray tip. Water inlet is blocked. Clear inlet. Inadequate water supply. Provide adequate water flow. Pump has following Inlet hose is kinked or leaking. Straighten inlet hose, patch leak.
Exploded Views and Parts Lists Section EXPLODED VIEW AND PARTS LIST — UNIT Item Part # Description Item Part # Description B190156GS BASE 10 95519GS QUICK CONNECT, Wand End B187602GS HANDLE 11 95518GS QUICK CONNECT, Wand/Acc 192088GS ASSY, Billboard 12 190147GS PUSHNUT 190249GS HOSE...
Page 19
Section 8: Exploded Views and Parts Lists EXPLODED VIEW AND PARTS LIST — PUMP Item Part # Description Item Part # Description 190568GS SEAL 76 21783GS THERMAL RELIEF 190569GS RETAINER RING 77 190585GS OIL BOTTLE 190671GS ENGINE ADAPTER & BEARING 190672GS KIT, WOBBLE PLATE BEARING 19 190571GS...
Page 20
Sección Reglas de Seguridad TABLA DE CONTENIDOS REGLAS DE SEGURIDAD Reglas De Seguridad ......20-22 Éste es el símbolo de alerta de seguridad.
Sección 1: Reglas de Seguridad PELIGRO ADVERTENCIA Al motor funcionar, se produce monóxido de La gasolina y sus vapores son extremadamente carbono, un gas inodoro y venenoso. inflamables y explosivos. El respirar el monóxido de carbono, producirá El fuego o una explosión pueden causar quemaduras náusea, desmayo o la muerte.
Page 22
Sección 1: Reglas de Seguridad ADVERTENCIA PRECAUCIÓN El lavadora de presión produce un rocío alto de la presión Los motores en funcionamiento producen calor y cuál riesgo de aumentos de la herida y dañe a la unidad. gases de escape a altas temperaturas. La temperatura del silenciador y de las zonas cercanas puede alcanzar •...
Sección Características y Controles CONOZCA SU MAQUINA LAVADORA DE PRESION Lea el manual del propietario y las reglas de seguridad antes de poner en marcha su máquina lavadora a presión. Compare las ilustraciones con su máquina lavadora a presión para familiarizarse con las ubicaciones de los diferentes controles y ajustes. Guarde este manual para referencias futuras.
Sección Montaje MONTAJE PREPARANDO EL LAVADOR A PRESIÓN PARA SU USO IMPORTANTE: Lea totalmente el manual del propietario antes que intente ensamblar u operar su lavador a presión. Si usted tiene un problema al ensamblar la unidad o si hacen falta Remueva el Lavador a Presión del algunas piezas o se encuentran dañadas, llame a la línea directa del lavador a presión, al 1-888-611-6708.
Page 25
Sección 3: Montaje Coloque el manubrio sobre los soportes del mismo que ya Figure 26 — Deslice Manga Química en el Clip de Metal están adheridos a la unidad principal. Asegúrese de que los orificios en el manubrio estén alineados con los orificios en los soportes del mismo manubrio (Figura 23).
Page 26
Sección 3: Montaje Conecte la Manguera y el Suministro de Antes de que conecte la manguera de jardín a la entrada de agua, inspeccione el colador de la entrada (Figura 31). Limpie Agua a la Bomba el colador si tiene residuos o solicite su remplazo si está IMPORTANTE: Usted deberá...
Sección Operación Revise que todas las conexiones de las mangueras (alta presión Coloque el coloró rápido conecta puntas de rocío en las y suministro de agua) estén apretadas correctamente y que no ranuras en el poseedor eso’s conectado a la extensión de la existan dobleces, cortes o daño de la manguera de alta presión.
Page 28
Sección 4: Operación Utilización de la Charola de Accesorios Figura 36 — Rocíe los Modelos del Rocío de Punta El unidad está equipado con una charola de accesorios. Posee tres La Presión Baja orificios para sostener la extensión de su boquilla, su varilla turbo y su cepillo, así...
Page 29
Sección 4: Operación IMPORTANTE: Usted deberá lavar el sistema de inyección de PRECAUCIÓN químicos después de cada uso colocando el filtro en un balde de agua limpia y haciendo funcionar la máquina lavadora a presión de Usted deberá conectar todas las mangueras antes de darle 1 a 2 minutos en el modo de baja presión.
Sección Mantenimiento RECOMENDACIONES GENERALES ADVERTENCIA La garantía de la máquina lavadora a presión no cubre los elementos La corriente de agua de alta presión que produce que han sido sujetos a abuso o negligencia por parte del operador. este equipo pueden perforar la piel y sus tejidos Para hacer válida la cobertura total de la garantía, el operador deberá...
Sección 5: Mantenimiento Retire la pistola y la extensión para boquillas de la manguera limpie inmediatamente la puntas de rocío usando las herramientas de alta presión. Retire la extensión para boquillas de la incluidas con su lavador a presión y siga las instrucciones siguientes: pistola y retire el anillo 'o' y el colador de la extensión para Apague el motor y apague el suministro de agua.
Sección 5: Mantenimiento Mantenimiento de la Bomba MANTENIMIENTO DEL MOTOR Consulte el manual del propietario del motor para las Cambio del aceite de la bomba instrucciones de cómo mantener adecuadamente el motor. Cambie el aceite cada 50 horas o una vez al año, lo que suceda antes.
Sección Almacenamiento PREPARANDO LA UNIDAD PARA PRECAUCIÓN SU ALMACENAMIENTO Usted deberá proteger su unidad de las temperaturas de congelamiento. El agua no debe permanecer en la unidad por un largo periodo de • Si no lo hace, dañará permanentemente la bomba y la unidad no tiempo.
Sección Diagnosticos de Averías REPARACION DE DAÑOS Problema Causa Solución Está usando la puntas de rocío de baja Cambie la puntas de rocío a una de las tres presión (negra). puntas de rocío de alta presión. La entrada de agua está bloqueada. Limpie la entrada.
GARANTÍA LIMITADA "Troy-Bilt® es una marca registrada de MTD bajo licencia de Briggs & Stratton Power Products. Briggs & Stratton Power Products reparará o sustituirá sin cargo alguno cualquier componente del equipo** que presente defectos de materiales y/o mano de obra. Los gastos de transporte de las piezas enviadas para reparar o sustituir conforme a los términos de esta garantía correrán a cargo del...
Page 36
LIMITED WARRANTY “Troy-Bilt® is a registered trademark of MTD and is used under license to Briggs & Stratton Power Products. Briggs & Stratton Power Products will repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.