Page 1
Troy-Bilt® is a registered trademark of MTD and is used under license to Briggs & Stratton Power Products. Troy-Bilt® es una marca registrada registrada de MTD y se usa abajo licencia a Briggs & Stratton Power Products. BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON,WISCONSIN, U.S.A.
Section 1: Safety Rules WARNING DANGER Fuel and its vapors are extremely flammable and Running engine gives off carbon monoxide, an explosive. odorless, colorless, poison gas. Fire or explosion can cause severe burns or Some chemicals or detergents may be harmful if death.
Page 4
Section 1: Safety Rules WARNING CAUTION Excessively high or low operating speeds increase risk Running engines produce heat and hot exhaust of injury and damage to pressure washer. gases.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C). •...
Features and Controls Section KNOW YOUR PRESSURE WASHER Read this owner’s manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Spray Gun Recoil Starter High Pressure Hose...
Assembly Section ASSEMBLY To prepare your pressure washer for operation, you will need to perform these tasks: IMPORTANT: Read entire owner’s manual before you Fill out and send in registration card. attempt to assemble or operate your new pressure washer. Attach handle to main unit.
Section 3: Assembly Connect Hose and Water Supply to Figure 3 — Attach “L” Hooks to Handle Pump IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses Spray Gun before you start the engine. Hook Hose Hook Attach one end of high pressure hose to high pressure...
Section 3: Assembly Before connecting garden hose to water inlet, inspect Turn ON water and squeeze trigger on spray gun to inlet screen (Figure 6). Clean screen if it contains debris, purge the pump system of air and impurities. replace it if it is damaged. DO NOT RUN PRESSURE WARNING WASHER IF SCREEN IS DAMAGED.
Operation Section HOW TO USE PRESSURE Attach nozzle extension to spray gun (Figure 7). Tighten by hand. WASHER Figure 7 — Connect Nozzle Extension to Spray Gun If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-888-611-6708.
Section 4: Operation How to Stop Pressure Washer Point nozzle down towards a firm surface and press trigger to test spray pattern (Figure 10). • Turn engine off according to instructions given in engine Figure 10 — Test the Spray Pattern owner’s manual.
Section 4: Operation Applying Detergent with the Pressure Washer Rinsing Adjustable Nozzle For Rinsing: IMPORTANT: Use soaps designed specifically for Slide nozzle backward to high pressure, press trigger pressure washers. Household detergents could damage and wait for detergent to clear. the pump.
Maintenance Section GENERAL MAINTENANCE WARNING RECOMMENDATIONS The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and The pressure washer warranty does not cover items that possible amputation. have been subjected to operator abuse or negligence.To receive full value from the warranty, the operator must •...
Section 5: Maintenance Detach spray gun and nozzle extension from high Detach nozzle extension from spray gun.Twist nozzle pressure hose. Detach nozzle extension from spray gun clockwise to stream position. Using supplied 2mm and remove o-ring and screen from nozzle extension. (5/64) allen wrench, remove orifice from end of nozzle Flush the screen, spray gun, and adjustable nozzle extension (Figure 13).
Section 5: Maintenance An O–Ring Maintenance Kit is provided with your pressure ENGINE MAINTENANCE washer which includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided See the engine owner’s manual for instructions on how to in the kit to service your unit’s o-rings.
Section Storage PREPARING THE UNIT NOTE: PumpSaver, model number 01559, is available as an optional accessory. It is not included with the pressure washer. FOR STORAGE Contact the nearest authorized service center to purchase PumpSaver. Water should not remain in the unit for long periods of CAUTION time.
Section Troubleshooting TROUBLESHOOTING Problem Cause Correction Nozzle in low pressure mode. Pull nozzle backward for high pressure mode. Water inlet is blocked. Clear inlet. Pump has following Inadequate water supply. Provide adequate water flow. problems: failure to Inlet hose is kinked or leaking. Straighten inlet hose, patch leak.
Exploded Views and Parts Lists Section EXPLODED VIEW AND PARTS LIST — UNIT Item Part # Description Item Part # Description 192422GS BASE 10 21760GS ORIFICE B191874GS HANDLE 11 192309GS KIT, Hook 191909GS BILLBOARD 12 192050GS KIT, E-Ring 190249GS HOSE 13 188792HGS WAND, Adjustable Nozzle 192645GS...
Section 8: Exploded Views and Parts Lists EXPLODED VIEW AND PARTS LIST — PUMP Item Part # Description Item Part # Description 19 190571GS CAP, Oil 193804GS KIT,WOBBLE PLATE BEARING 23 193817GS HOUSING, Piston 190632GS KIT,WATER INLET, ALUM 28 190627GS MANIFOLD 190634GS KIT, OUTLET, ALUM...
Page 20
Sección Reglas de Seguridad TABLA DE CONTENIDOS REGLAS DE SEGURIDAD Reglas De Seguridad ....... . 20-22 Éste es el símbolo de alerta de seguridad.
Sección 1: Reglas de Seguridad PELIGRO ADVERTENCIA Al motor funcionar, se produce monóxido de La gasolina y sus vapores son extremadamente carbono, un gas inodoro y venenoso. inflamables y explosivos. El respirar el monóxido de carbono, producirá El fuego o una explosión pueden causar quemaduras náusea, desmayo o la muerte.
Page 22
Sección 1: Reglas de Seguridad ADVERTENCIA PRECAUCIÓN El lavadora de presión produce un rocío alto de la presión Los motores en funcionamiento producen calor y cuál riesgo de aumentos de la herida y dañe a la unidad. gases de escape a altas temperaturas. La temperatura del silenciador y de las zonas cercanas puede alcanzar •...
Sección Características y Controles CONOZCA SU MAQUINA LAVADORA DE PRESION Lea el manual del propietario y las reglas de seguridad antes de poner en marcha su máquina lavadora a presión. Compare las ilustraciones con su máquina lavadora a presión para familiarizarse con las ubicaciones de los diferentes controles y ajustes. Guarde este manual para referencias futuras.
Sección Montaje MONTAJE A prepara su arandela de la presión para la operación, usted necesitará a realiza estas tareas: IMPORTANTE: Lea totalmente el manual del propietario antes Llene y mande en tarjeta de matrícula. que intente ensamblar u operar su lavador a presión. Conecte manubrio a unidad principal.
Page 25
Sección 3: Montaje Inserte el "L" gancho del agujero apenas bajo la cartelera en Conecte la Manguera y el Suministro de el derecho de la manija (visto desde la parte posterior de la Agua a la Bomba unidad). Sostenga el gancho en lugar con los alicates y asocie IMPORTANTE: Usted deberá...
Page 26
Sección 3: Montaje Antes de que conecte la manguera de jardín a la entrada de agua, ABRA el suministro del agua (abra la válvula de suministro inspeccione el colador de la entrada (Figura 22). Limpie el completamente). colador si tiene residuos o solicite su remplazo si está dañado. ADVERTENCIA NO HAGA FUNCIONAR LA MÁQUINA LAVADORA A PRESIÓN SI EL COLADOR DE LA ENTRADA ESTÁ...
Sección Operación CÓMO USAR SU MÁQUINA Apriete el gatillo en la pistola rociadora (asegúrese de que la lanza se encuentra en el modo de baja presión) para LAVADORA A PRESIÓN deshacerse de la presión del aire causada al prender el agua. El agua se descargara de la pistola del spray en un chorro Si tiene problemas operando su máquina lavadora a presión, por muy Delgado.
Page 28
Sección 4: Operación Cómo Usar la Boquilla Ajustable El patrón de rociado se ajusta de un patrón angosto a un patrón en abanico girando la boquilla (Figura 27). Usted ya debe saber como darle ARRANQUE a su máquina Figura 27 — Ajustar el Patrón de Aspersión lavadora a presión y como DETENERLA.
Page 29
Sección 4: Operación Mantenga la pistola de rociado a una distancia segura del área PRECAUCIÓN que planea rociar. Evite que el tubo de inyección de químicos entre en contacto Aplique un rociado de alta presión en un área pequeña, con el silenciador caliente. después revise si la superficie presenta daños.
Sección Mantenimiento RECOMENDACIONES GENERALES Chequee el Tubo de Sifón del Detergente La garantía de la máquina lavadora a presión no cubre los elementos Examine el filtro en el tubo del detergente y límpielo si se que han sido sujetos a abuso o negligencia por parte del operador. encuentra sucio.
Page 31
Sección 5: Mantenimiento Coloque el colador ejerciendo presión con el borrador de Figura 29 - Remover y Limpiar la Boquilla un lápiz hasta que se asiente por completo en el fondo de la abertura.Tenga cuidado de no doblar el colador. Coloque el anillo 'o' en la ranura respectiva.
Sección 5: Mantenimiento Para retirar un anillo 'O' desgastado o dañado, utilice un MANTENIMIENTO DEL MOTOR destornillador de cabeza plana pequeño, colóquelo por debajo del Consulte el manual del propietario del motor para las anillo 'o' y sáquelo haciendo palanca. instrucciones de cómo mantener adecuadamente el motor.
Sección Almacenamiento PREPARANDO LA UNIDAD PARA PRECAUCIÓN SU ALMACENAMIENTO Usted deberá proteger su unidad de las temperaturas de congelamiento. El agua no debe permanecer en la unidad por un largo periodo de tiempo. Los sedimentos o minerales se pueden depositar en las •...
Sección Diagnosticos de Averías DIAGNOSTICOS DE AVERÍAS Problema Causa Solución La boquilla está en el modo de baja presión. Mueva la boquilla hacia atrás para el modo de alta presión. La entrada de agua está bloqueada. Limpie la entrada. Suministro de agua inadecuado. Proporcione flujo de agua adecuado.
GARANTÍA LIMITADA "Troy-Bilt® es una marca registrada de MTD bajo licencia de Briggs & Stratton Power Products. Briggs & Stratton Power Products reparará o sustituirá sin cargo alguno cualquier componente del equipo** que presente defectos de materiales y/o mano de obra. Los gastos de transporte de las piezas enviadas para reparar o sustituir conforme a los términos de esta garantía correrán a cargo del...
Page 36
LIMITED WARRANTY “Troy-Bilt® is a registered trademark of MTD and is used under license to Briggs & Stratton Power Products. Briggs & Stratton Power Products will repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.Transportation charges on parts submitted for repair or replacement under this...
Need help?
Do you have a question about the 1902 and is the answer not in the manual?
Questions and answers
What oil type to put into pressure washer model 01902