Related Manuals for Titan TTL488GDO
Summary of Contents for Titan TTL488GDO
- Page 1 SAFETY AND OPERATING MANUAL Original instructions (Version 1.0_201209) 25CC PETROL MULTI TOOL TTL488GDO...
-
Page 3: Safety Instructions
- Never remove the fuel tank cap or add fuel with the power source running. Allow engine and exhaust components to cool down before refuelling. - Do not smoke while operating fueling or starting this machine . - Never refuel indoors or in unconfirmed spaces. 25CC PETROL MULTI TOOL TTL488GDO... - Page 4 - Never store the product or fuel container inside where there is an open flame, such as near a water heater. - If fuel is spilled, do not attempt to start the product, but move it away from the area of spillage before starting.
- Page 5 GRASS TRIMMER SAFETY INSTRUCTIONS 1. Wear head protection, where there is a risk of falling objects. 2. Wear eye protection (goggles or face shield). 3. Wear ear protection. 4. Wear foot protection and gloves. 25CC PETROL MULTI TOOL TTL488GDO...
- Page 6 5. Keep a distance between the product and bystanders of at least 15 m. 6. Beware of thrown object. 7. Take care against injury from any device fitted for trimming the filament line length. After extending new cutting device line always return the product to its normal operating position before switching on.
- Page 7 This field may under some circumstances interfere with active or passive medical implants! To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their doctor and the medical implant manufacturer before operating this product! 25CC PETROL MULTI TOOL TTL488GDO...
- Page 8 VIBRATION The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to provide indicative vibration test results to enable users to make informed decisions as to the period of time a power tool can be used safely on a daily basis and the choice of tool.
- Page 9 Plan your work schedule to spread any high vibration tool use across a number of days. Health Surveillance. Health Surveillance. All employees should be part of an employer's health surveillance scheme to help identity any vibration related diseases at an early stage, prevent disease progression and help employees stay in work. 25CC PETROL MULTI TOOL TTL488GDO...
- Page 10 SYMBOLS Warning Read the instruction manual Compliance with relevant safety standards Wear ear protection Wear eye protection Wear safety helmet! Wear respiratory protection Wear face protection! Gloves with saw protection Wear safety footwear Wear protective clothing Objects thrown by the product could hit the user or other bystanders. Always ensure that other people and pets remain at a safe distance from the product when it is in operation.
- Page 11 Inspect the area where the product is to be used and remove all objects which can be thrown by the product. If objects are found while operating, stop the engine and remove the object Do not use metal blades Use a line spool only. 25CC PETROL MULTI TOOL TTL488GDO...
- Page 12 Location of starter handle: pull upwards Do not touch the cutting device until it stops completely. Guaranteed sound power level Risk of long hair being drawn into air inlet. Risk of loose clothing being drawn into air intake. Keep other people out of working area during operation. A distance of at least 15m must be observed.
- Page 13 25CC PETROL MULTI TOOL TTL488GDO...
- Page 14 A. Main unit Air vents Spark plug connector Choke lever Primer Air filter case Fuel tank cap Recoil starter handle Harness Securing clip Step guard Clamp Locking pin Locking knob Auxiliary handle Control unit Handle grip Throttle trigger Ignition switch on/off Throttle interlock...
- Page 15 B. Grass trimmer Shaft Spindle Trimming guard Line cutter Trimmer head Trimming line Bumper 25CC PETROL MULTI TOOL TTL488GDO...
- Page 16 C. Hedge trimmer attachment Hedging blade Blade protection sheath Bolts Unlock levers Locking pin Hedge trimmer shaft Gripping surface...
- Page 17 Multi tool I: Cross-head screw driver / socket wrench rod (used with Multi tool II) Multi tool II: Spark plug wrench / socket wrench (used with Multi tool I) Hex key 5 mm Hex key 4 mm 25CC PETROL MULTI TOOL TTL488GDO...
-
Page 18: Technical Data
TECHNICAL DATA GENERAL Engine type Sl33, air cooled 2-stroke Engine displacement 25cc Max. engine power 0.8 kW Max. engine speed 10500 /min Engine idle speed 3000 /min Clutch engagement speed 4500 /min Fuel tank volume 500 ml Fuel type #95 unleaded, in a 40:1 ratio mix with 2 stroke oil Fuel consumption at maximum engine power 0.38 kg/h... - Page 19 Net weight (with hedge trimmer attachments) 7.0 kg The sound intensity level for the operator may exceed 85dB(A) and ear protection measures are necessary. ACCESSORIES HARNESS MULTI TOOL 1 PC HEX KEY (4MM) HEX KEY (5MM) 25CC PETROL MULTI TOOL TTL488GDO...
-
Page 20: Operation Instructions
OPERATION INSTRUCTIONS WARNING! Read all instructions carefully. Do not connect the spark plug before it is completely assembled. Always use gloves during assembly. INTENED USE 1. This 2 in 1 petrol multi tool is designated with an engine displacement of 25CC. Depending on the attached accessory this product is intended to be used as: 1). - Page 21 (A11). Release the locking pin and ensure it engages in the hole. (See Fig. 3b) c) Secure the connection by tightening the locking knob (A13) clockwise. (See Fig. 3c) Fig. 3b Fig. 3c 25CC PETROL MULTI TOOL TTL488GDO...
- Page 22 2). Safety guard assembly Warning: Take great care when fitting the guard. The guard is fitted with a very sharp cutting edge. Please note for your safety the cutting edge is covered with a blade cover. a). Remove the bolt and screw nut on the guard (B3). b).Place the guard over the end of the spindle (B2) and align the holes in the front of the guard with the Fig.
- Page 23 8). Wipe up spilled fuel with a soft cloth and refit the fuel tank cap (A6). Fig. 8c 9). Always dispose of fuel, used oil and soiled objects according to local regulations (see section “Environmental Protection”). 25CC PETROL MULTI TOOL TTL488GDO...
- Page 24 NOTE: Fuel and oil deteriorate over time. It may be difficult to start the engine if you use fuel which has been kept for more than 30 days. Towards the end of the season, it is advisable to put only as much fuel in the tank as you need for each mowing of the lawn, since it should be completely used up before storing the product.
- Page 25 6 times until fuel is visible. (See Fig. 13c) d). If the engine is warm, move the choke lever (A3) to the “OPEN” position , do not press the primer. (See Fig. 13d) Fig. 13b Fig. 13c Fig. 13d 25CC PETROL MULTI TOOL TTL488GDO...
- Page 26 e). Hold the product stable and pull the recoil starter handle (A7) firmly; repeat until the engine starts. (See Fig. 13e) WARNING! Make sure that the cutting blade is not touching the ground or other objects when starting the product! Allow the recoil starter rope to return slowly and controlled after each pull! f).
- Page 27 11). For best results, do not cut wet grass because it tends to stick to the cutting heads and guard, prevents Fig. 15d proper discharge of grass trimmings, and could cause you to slip and fall. Fig. 15e Fig. 15f 25CC PETROL MULTI TOOL TTL488GDO...
- Page 28 12). Pay special attention when performing the work close to trees and bushes. The cutting heads could damage sensitive bark, and damage fence posts. (See Fig. 15g) 8. HEDGE TRIMMER 1). Angle adjustment Adjust the attachment angle to fit the growth of the plant.
- Page 29 9. AFTER USE 1). Switch the product off, allow the engine to cool down and then remove the spark plug connector. 2). Check, clean and store the product as described below. Fig. 17c Fig. 17d 25CC PETROL MULTI TOOL TTL488GDO...
-
Page 30: Maintenance
MAINTENANCE WARNING! Always switch the product off, let the product cool down and disconnect the spark plug connector before performing inspection, maintenance and cleaning work! WARNING! Only perform repairs and maintenance work according to these instructions! All further works must be performed by a qualified specialist! WARNING! Wear safety gloves when working on the attachment heads and close to it! Use... -
Page 31: Blade
The fuel tank of this product is fitted with a filter located at the free end of the fuel pipe. Ask an authorised service centre or similar qualified person to check and where necessary replace it at regular intervals. 25CC PETROL MULTI TOOL TTL488GDO... - Page 32 SPARK PLUG NOTE! This engine uses a CHAMPION RCJ6Y spark plug with 0.6-0.7mm electrode gaps. Use a suitable replacement and replace once a year. You can it replace with “CHAMPION” or “NGK” as an alternative. 1. Inspect the spark plug at least every 25 hours or prior to long-term storage over 30 days if the use has not been this high.
- Page 33 3. The product comes in a package that protects it against damages during shipping. Keep the package until you are sure that all parts have been delivered and the product is function properly. Recycle the package afterwards. 25CC PETROL MULTI TOOL TTL488GDO...
-
Page 34: Troubleshooting
TROUBLESHOOTING WARNING! Suspected malfunctions are often due to causes that the user can fix themselves Therefore check the product using this section. In most cases the problem can be solved quickly. WARNING! Only perform the steps described within these instructions! All further inspection, maintenance and repair work must be performed by an authorised service centre or a similarly qualified specialist if you cannot solve the problem yourself! Problem... -
Page 35: Declaration Of Conformity
EN ISO 10517:2009 EN ISO 14982:2009 Authorised signatory and technical file holder Date: 02/08/12 Signature: __________________ Name / title: Peter Harries / Quality Manager Titan Power Tools (UK) Ltd, Trade House, Mead Avenue, BA22 8RT 25CC PETROL MULTI TOOL TTL488GDO...