Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lindemann 882
Summary of Contents for Lindemann 882
- Page 1 Integrated Amplifier Owner’s Manual...
-
Page 2: Important Safety Precautions
882 Integrated Amplifier Important Safety Precautions • Use only an approved power cable and plug or distribution board to connect your amplifier to a power outlet. Do not use an extension cable. • Never touch the mains plug if your hands are wet. -
Page 3: Copyright And Trade Mark Acknowledgements
Keep the carton and packaging materials that your 882 came in. They will protect your integrated amplifier should you need to transport it in the future. Transporting the 882 in anything other than the original packaging may result in physical damage not covered by your warranty. -
Page 4: Table Of Contents
Directive on waste electrical and electronic equipment Accessories supplied • 882 Integrated Amplifier • System remote control • Power cable, 2 metres • SYSCOM cable, 1 metre • Owner's Manual We recommend that you keep the packaging for use when transporting the 882 in the future. - Page 5 Avoid placing the integrated amplifier close to loudspeakers or any other source of vibration. The 882 will respond to these measures by performing at its best. Never stack the 882 directly on other items of equipment. Vibrations from mains transformers and electro-magnetic interference from other components can have a negative impact on the integrated amplifier’s sound quality.
-
Page 6: Front View
The input selector is the equivalent of the LEFT/RIGHT buttons on the remote control. Power Press the POWER button to turn the unit on and off. The 882 must be connected to the mains, with the power switch on the rear panel in the 'on' position (position I). -
Page 7: Volume Control
882 Integrated Amplifier Setup This button opens the configuration menu and provides access to the more advanced integrated amplifier functions. To quit, press the SETUP button repeatedly until the standard display reappears. Enter Confirm your input. This is the equivalent of the OK button on the remote control. -
Page 8: Rear View
Analog output XLR left Phono ground Analog inputs The 882 is equipped with both balanced (XLR) and unbalanced (RCA) analog inputs. Connect the outputs from your source equipment to the appropriate inputs on your integrated amplifier. Make sure that the plugs are a snug fit! Poorly fitting RCA plugs can detract considerably from the sound quality of your hi-fi system. -
Page 9: Analog Outputs
Pin 3: Signal - Speaker terminals The speaker outputs on the 882 are in the form of terminal posts. These are for use with cables terminated with spades or 4mm (banana) plugs. Please remember: the 882 is a fully balanced amplifier! This means that both the red and the black speaker terminals on each channel are connected directly to an amplifier output. -
Page 10: Remote Control
882 Integrated Amplifier Remote control Power button Switches the unit on and off from standby. Menu selection Selects the amplifier's configuration menu. Mute Reduces the level of the outputs to zero. Navigation cluster Normal operation: UP/DOWN: Volume adjustment +/- LEFT/RIGHT:... -
Page 11: Using The 882 For The First Time
Please note: the 820 SACD-Player is to be connected to input 2 of the integrated amplifier. This is mandatory to use the digital inputs select feature of the 882. Input 1 is normally used as an input for turntable preamplifiers. •... -
Page 12: Basic Amplifier Controls
820's four digital inputs from the 882 (inputs 6-9). To use these digital inputs, you must connect the balanced analog output of the 820 to Input 2 on the 882. When you select a digital input on the 882, the blue LED for Input 2 (analog input) illuminates together with the yellow LED to indicate that a digital input is active. -
Page 13: Adjusting The Volume
882 Integrated Amplifier Adjusting the volume To adjust the volume, use the UP or DOWN buttons on the remote control, or the volume control knob on the front panel. When adjusting the volume with the remote, the speed of adjustment depends on how long you keep your finger on the UP/DOWN buttons. -
Page 14: Cooling
882 Integrated Amplifier Cooling The amount of heat generated by the 882 depends on how hard it is driven. It is very important to ensure that there is unimpeded circulation of fresh air from below and that hot air can escape behind and above the unit. When you install your amplifier, therefore, make sure to provide adequate clearance above and behind the unit. -
Page 15: Configuration Menu
882 Integrated Amplifier Configuration menu The 882 provides many adjustment options in addition to the basic controls. You can access these functions in AMP Setup. To open the menu, press the AMP or SETUP buttons. To navigate within the Setup, use the LEFT or RIGHT buttons on the remote control, or use the input selector on the front panel. -
Page 16: Balance
Display Brightness When you start using the 882, its display is set to maximum brightness. After about 15 seconds, the display changes to the brightness setting you have specified in the display brightness menu. To avoid wearing out the display prematurely, do not set the display brightness too high. -
Page 17: Inputs
OK button. If you have an 820 connected to your system (SYSCOM), the names of its digital inputs will appear on the 882. You can only change the names of the digital inputs via the DAC menu on the 820. -
Page 18: Link Mode
882 Integrated Amplifier Link Mode The 882 is able to communicate with other Lindemann components of the 800 range via SYSCOM. This Link Mode allows a single remote control to be used for all Lindemann components. To use this feature, all components must be linked with a SYSCOM cable (see diagram below). -
Page 19: Troubleshooting
• The 882 is not connected to a power outlet, or the power switch (on the rear panel) is in the off position. -> Plug the 882 into a power outlet and switch the unit on. The display illuminates but there is no sound: •... -
Page 20: Specifications
882 Integrated Amplifier Specifications Measuring conditions: 22°C, 230V supply voltage. Dimensions..............440*135*360 mm (W*H*D incl. feet) Weight ........................... 20.4 kg AC supply ......................230 V 50/60 Hz Power consumption (idle) ....................75 W Power consumption (full power).............. 800W maximum Power consumption (stand-by) ..................0.5W... -
Page 21: Ce Declaration Of Conformity
Integrated Amplifier Model: 882 Stereo Integrated Amplifier LINDEMANN audiotechnik GmbH declares that this product complies with the Low Voltage Directive 73/23/EEC and the Electromagnetic Compatibility Directive 89/336/EEC, amended by the directives 92/31/EEC and 93/68/EEC. The conformity of the designated product with the provisions of directive... -
Page 22: Guarantee And Service
This product is guaranteed under the conditions that apply in the country of purchase and your statutory rights are not limited. In addition to any statutory rights you may have, Lindemann undertake to replace any parts that have failed due to faulty manufacture. To help us, please ask your Lindemann retailer about the Lindemann warranty scheme in operation in your country. -
Page 23: Directive On Waste Electrical And Electronic Equipment
882 Integrated Amplifier Directive on waste electrical and electronic equipment Electronic equipment should not be disposed of with household waste but in compliance with the Directive 2002/96/EU of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment. When this equipment reaches the end of its working life, please take it to one of the available collection points. - Page 24 882 Integrated Amplifier • Owners´s Manual / English /Rev.1 • 812 Lindemann audiotechnik GmbH • Felix-Wankel-Str. 4 • D-82152 Krailling • Germany Web www.lindemann-audio.de • E-mail info@lindemann-audio.de Tel +49 (0)89 8913679-0 • Fax +49 (0)89 8913679-29...