Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H0603
Summary of Contents for Grizzly H0603
- Page 1 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA...
- Page 2 H0603 18V Cordless Drill and Saw...
-
Page 3: Safety Instructions For Power Tools
Keep work area well lighted. H0603 18V Cordless Drill and Saw SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. - Page 4 Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. H0603 18V Cordless Drill and Saw PARTS.
-
Page 5: Additional Safety
Do not throw battery in fire. Combustion of some of the batter- ies’ component materials can cause toxic fumes and possible explosion. H0603 18V Cordless Drill and Saw pack before BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. Consult your local Yellow Pages directory under the category “Recycling”... - Page 6 Commentary We are proud to offer the Grizzly Model H0603 18V Cordless Drill and Saw. The Model H0603 is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...
-
Page 7: Drill Operations
A steady red light over the word “ON” should come on indicating the battery is being charged. When the battery is fully charged, the H0603 18V Cordless Drill and Saw ® /Straight Inserting Battery Into Drill Inserting and Removing Bits Never leave a battery unattend- ed while charging. - Page 8 Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety pre- cautions are overlooked or ignored, serious personal injury may occur. H0603 18V Cordless Drill and Saw...
-
Page 9: Operating The Drill
Torque Setting Direction Switch ON/OFF Trigger H0603 18V Cordless Drill and Saw Fig 2. Location of controls. embossed on the drill case. Set on “1” for very light applications such as dri- ving screws into drywall. Use the higher settings for denser woods and materials. -
Page 10: Drill Maintenance
Battery must be recycled or disposed of properly. Refer to the Grizzly catalog for replacement batteries. Disassembly and improper reassem- bly of this device can result in electri- cal shock danger. - Page 11 Angle Lock Knob: Used when changing Edge Guide Lock Screw: Used with Dust Port: The 1 Guide Notch: Provides a visual guide for H0603 18V Cordless Drill and Saw Fig 3. Top view. installing or removing blades. adjusting base height / depth of cut.
- Page 12 4mm Allen ® Wrench: Used on blade retaining screw to install and remove blades. Battery: 18 volt battery for use with this saw. Positive Stop Screw: Adjusts so that base stops at 90° to blade. H0603 18V Cordless Drill and Saw...
- Page 13 Be careful to avoid touching the saw teeth, and slip the blade out of the saw. H0603 18V Cordless Drill and Saw Insure the teeth on the new blade are in the correct orientation and place the blade on the arbor, then the washer and screw.
-
Page 14: Cutting Depth Adjustment
Adjust the base so that the edge of the square contacts the the full face of the exposed part of the blade. Tighten the angle locking knob. Fig 8. Base angle adjustment. H0603 18V Cordless Drill and Saw 90° Stop... - Page 15 Blade thicknesses can vary, causing the scale on the edge guide to read inaccurately. H0603 18V Cordless Drill and Saw Guide Notch and Scale: The trim saw is provided with a Guide Notch and Scale. These are located on the leading edge of the saw base.
- Page 16 Let go of the trigger when finished with the cut. Avoid kickback hazards! If saw motor stalls during cut release the trigger immediately. Determine the cause of the problem and rectify before continu- ing cut. Fig 9. Proper Holding Grip. H0603 18V Cordless Drill and Saw...
- Page 17 Know your worksite. Only saw as deep as necessary. Check behind walls for for wires, other electrical hazards, or plumbing. H0603 18V Cordless Drill and Saw Maintenance Your cordless power tool will give you hun- dreds of hours of operation time before ever needing service.
-
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. - Page 19 NOTES H0603 18V Cordless Drill and Saw...
- Page 20 NOTES H0603 18V Cordless Drill and Saw...
-
Page 21: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 22 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
Need help?
Do you have a question about the H0603 and is the answer not in the manual?
Questions and answers