Page 1
XPower Charger 2 1-800-670-0707 (toll free in North America) 1-360-925-5097 (direct) 1-800-994-7828 (toll free in North America) 1-360-925-5143 (direct) e CustomerService@xantrex.com www.xantrex.com Owner's Guide 975-0135-01-01 REV. B Printed in China...
Page 2
XPower Charger 2 Owner’s Guide About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to MW utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-alone systems.
Trademarks XPower by Xantrex is a trademark of Xantrex International. Xantrex is a registered trademark of Xantrex International. Other trademarks, registered trademarks, and product names are the property of their respective owners and are used herein for identification purposes only.
1 Introduction Thank you for purchasing a Xantrex XPower Charger 2. The XPower Charger 2 is part of a family of ultra-compact, light weight and modern power inverters and chargers from Xantrex Technology. About the XPower Charger 2 The 2 amp XPower Charger 2 is designed to charge 12 volt rechargeable batteries.
Warnings and Cautions WARNING: This guide contains important safety and operating instructions in how to use the XPower Charger 2, to recharge 12 volt batteries. Read this guide fully for safe operation of this charger. Save this guide for future reference.
Page 7
Do not expose the XPower Charger 2 to rain or snow. Use of an attachment not recommended may result in a risk of fire, electric shock, or injury to persons.
Page 8
Do not operate XPower Charger 2 with damaged cord or plug—replace the cord or plug immediately. Do not operate XPower Charger 2 if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified service technician.
WARNING: Risk of explosive gases Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason, it is of utmost importance that each time before using a battery charger, you read this guide and follow the instructions exactly.
Page 10
Use XPower Charger 2 for charging a LEAD-ACID battery only. It is only intended to charge lead-acid batteries or batteries, such as those used in specific integrated products.
Preparing to Charge If necessary to remove the battery from the vehicle to charge, always remove the grounded terminal from the battery first. Make sure all accessories in the vehicle are off, so to minimize chances of an arc. Be sure area around the battery is well- ventilated while battery is being charged.
Charger Location Place the battery charger as far away from the battery as the output DC cable permits. Never place the battery charger directly above a battery being charged; gases from battery will corrode and damage the charger. Never allow battery acid to drip on the charger when reading specific gravity or filling battery.
Page 13
Failure to follow these safety guidelines may cause personal injury and/or damage to the XPower Charger 2. It may also void your product warranty.
This section describes the main features of the XPower Charger 2. Front Panel Figure 1 shows the XPower Charger 2. Use Table 1 to identify the function of items. Figure 1 XPower Charger 2 Features Table 1 XPower Charger 2 Features...
Page 15
Charging light The red charging light indicates that charging is in progress. When the battery is fully charged, the red charging light will turn off. AC Cord Connects the XPower Charger 2 to a standard wall outlet...
DC Cable Connections Figure 2 shows the DC cable connections available for the XPower Charger 2. Use Table 2 to identify the usage. Figure 2 DC Cable Connections Table 2 DC Cable Connections Usage Item Function Battery clip adapter Lighter plug adapter...
Page 17
WARNING: Shock and fire hazard The battery clip adapter, lighter plug adapter, and ring terminal adapter are to be used individually with the XPower Charger 2 as specified in this manual. Connecting adapters together for other, non-specified use will result in reverse polarity and may result in...
4 Charging a 12 volt Battery It is possible to use XPower Charger 2 to charge most engine starting batteries when the battery is installed in a vehicle. Before attempting to charge a vehicle battery, make sure the battery is a 12 volt, lead-acid type.
Page 19
XPower Charger 2 to the vehicle battery. Plug the XPower Charger 2 AC cord into a standard 115 volt AC outlet. As the battery in your vehicle charges, the green Power light and red Charging light turn on.
Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons. Connect the XPower Charger 2 DC cable to the battery clip adapter. Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE (NEG, N, –) post.
Page 21
Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Plug the XPower Charger 2 AC cord into a standard 115 volt AC outlet. 10. As the battery in your vehicle charges, the green Power light and red Charging...
Page 22
CAUTION If the green Power light turns off and the red Charging light turns on, immediately disconnect the battery clips from the battery terminals. The unit has detected an output short circuit or reverse polarity on the DC connection. Check the connection. 11.
Page 23
Attach an insulated battery cable, at least 24-inches long, 6 gauge (AWG) to the NEGATIVE (NEG, N, –) battery post. Connect the XPower Charger 2 DC cable to the battery clips adapter. Connect the POSITIVE (RED) charge clip to the POSITIVE (POS, P, +) battery post.
Page 24
Plug the XPower Charger 2 cord into a standard 115 volt AC outlet. As the battery charges, the green Power light and red Charging light turn on. CAUTION If the green Power light turns off and the red Charging light turns on, immediately disconnect the clips from the battery terminals.
Using the Ring Terminal Adapter Follow these steps to install the ring terminal adapter: CAUTION Be sure the safety cap on the ring terminal adapter is put on before installing the adapter to the battery terminal. The ring terminal adapter’s leads have crimped, color-coded ring terminals (RED - POSITIVE and BLACK - NEGATIVE).
Page 26
Disconnect the DC safety cap on the ring terminal adapter. Insert the XPower Charger 2’s DC cable to ring terminal adapter connector. Plug the XPower Charger 2’s AC cord into a standard 115 volt AC outlet.
How long the charger has been in use • A brief description of the problem PROBLEM: Green Power light is off when XPower Charger 2 is connected to AC power. Possible cause Solution No AC power at outlet. Ensure power is present at outlet.
Page 28
Possible cause Solution High charging current Use a higher charging is detected. The battery current charger (such being charged requires as XPower higher charging Charger 15). current. A heavy load is Remove the load from connected to the the battery. battery being charged.
Warranty is provided by Xantrex Technology, Inc. ("Xantrex") and covers defects in workmanship and materials in your XPower Charger 2. This warranty period lasts for 12 months from the date of purchase at the point of sale to you, the original end user customer.
Page 31
For some products, Xantrex maintains a network of regional Authorized Service Centers. Call Xantrex or check our website to see if your product can be repaired at one of these facilities. What proof of purchase is required? In any warranty...
Page 32
This warranty does not apply to and Xantrex will not be responsible for any defect in or damage to: the product if it has been misused, neglected,...
Page 33
UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD STIPULATED UNDER THIS LIMITED WARRANTY. IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES, COSTS OR...
IN CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER MEDICAL EQUIPMENT OR DEVICES. Return Material Authorization Policy Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA) number and the correct factory "Ship To" address. Products must also be shipped prepaid.
USA or Canada In addition to the above, you MUST include return freight funds and are fully responsible for all documents, duties, tariffs, and deposits. If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex return material authorization (RMA) number is not required.
Out of Warranty Service If the warranty period for your XPower Charger 2 has expired, if the unit was damaged by misuse or incorrect installation, if other conditions of the warranty have not been met, or if no dated proof of purchase is available, your product may be serviced or replaced for a flat fee.