American Standard Whirlpool/Bathing Pool 2748.XXXW Installation Instructions

TOWN SQUARE®
5' x 42"™
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
ON/OFF
SWITCH
29-7/8"
(759mm)
14-1/2"
(368mm)
41-5/8"
(1057mm)
FLOOR CUTOUT
PROVIDE ACCESS
TO PUMP FOR
(127 X 305mm)
SERVICE ON ALL
INSTALLATIONS
PUMP
OUTLINE OF
JETS (6)
SKID RESISTANT
SURFACE
2" C/L OF
(51mm) OVERFLOW
5-3/4"
(146mm)
1-1/2" N.P.T.
THREADS
3-1/8"
3/4" 1-1/2" O.D.
(79mm)
(19mm)
TAILPIECE
HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"
DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY
29-7/8
(759mm)
TO END
OF TUB
FOR SPOUT
& VALVES
1-1/2
(38mm)
2-1/2
(64mm)
1-1/2
4-1/2
(38mm)
(114mm)
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately. After inspection and during installation, protect the bath from construction damage. After installation, and
before enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the
safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or
piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing
materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess
installations). If installing American Standard 2555.901 "Town Square" deck mount bath filler, please refer to hole
drilling location above.
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
753026-100 Rev. G
2748.XXXW SERIES
WHIRLPOOL/BATHING POOL
INSTALLATION INSTRUCTIONS
59-1/2"
(1511mm)
INTEGRAL
FITTING DECK
2-1/2" X 14"
(64 X 356mm)
5" X 12"
OUTLINE OF CUTOUT
SUCTION
58-1/4" X 40-1/4"
(1480 X 1022mm)
LEVELING STRINGER
PUMP
(NOT FOR SUPPORT)
SAFE-T-HEATER
REMOVABLE
BLANK
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
C/L
DRAIN
FITTINGS
DECK
FOR HAND
SPRAY
EDGE OF
FITTINGS
1-1/2
DECK
4-1/2 5
(38mm)
(114mm) (127mm)
THANK Y OU...
3"
for selecting an American Standard bath. Your
(76mm)
5-1/4"
new bath is shipped to you after careful
(133mm)
inspection. The whirlpool version is completely
assembled with pump, motor, and system piping.
All you need to finish the installation are your
C/L OF
selected fittings and electrical connections for a
DRAIN
OUTLET
whirlpool. To insure maximum performance and
EDGE OF
pleasure from this product, please follow the
FLOOR
CUTOUT instructions and cautions.
List of Optional Components (not included):
• Tile Bead Kit (P/N 751755-200)
• 5 Foot Apron 9460.018
• Safe-T-Heater 9075.120*
3/4"
(19mm)
List of Required Components (not included):
• Drain 1594.170
• Bath Filler
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
23"
• Pipe Wrench
(584mm)
21" • Slip Joint Pliers
(533mm)
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT 3
WHIRLPOOL PUMP
© American Standard Inc. 2007
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
GENERAL SPECIFICATIONS FOR 2742 WHIRLPOOL
71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm)
41 x 21-1/2 In. (1041 x 546mm)
62 x 31-1/2 In. (1574 x 800mm)
33 Lbs./Sq.Ft. (163 Kgs./Sq.m)
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 HP, 14.4 AMPS ,120V.
115 Lbs. (52 Kg.)
690 Lbs. (313 Kg.)
69 Gal. (261 L)
60 Gal. (227 L)
14-1/4 In. (362mm)
27.8
55.7