Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Lightspeed 800IX
Summary of Contents for Lightspeed 800IX
- Page 1 800iX Classroom Audio System U s e r M a n u a l...
- Page 3 Lightspeed’s popular 880iR and 850iR systems to create up to a four-channel solution for the classroom. The 800iX is a two-channel receiver that allows the use of up to two additional microphones simultaneously. A standard IR sensor can provide high quality reception in rooms up to 1600 square feet.
-
Page 4: Safety Instructions And Certifications
DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE —All warnings on 3. Heed Warnings REFER SERVICING TO QUALIFIED PERSONNEL this Lightspeed product and in these instructions should be followed. The lightning flash with arrowhead symbol —All operating 4. Follow Instructions... -
Page 5: Table Of Contents
..............SECTION 5: Troubleshooting, Daily Use and Warranty Troubleshooting Guide ........................Daily Use Instructions ........................Tips on Classroom Audio ......................Warranty Statement ........................System Specifications ........................Individual Components and Optional Accessories ..............User Notes ............................800iX User Manual | iii... -
Page 6: Section 1: System Overview
8 0 0 i X U s e r M a n u a l SECTION 1 System Overview 1 | 800iX User Manual... -
Page 7: System Components
8 0 0 i X U s e r M a n u a l SYSTEM COMPONENTS 800iX Infrared Wireless Microphone Receiver and Power Supply Sensor Cable SR-70F Infrared Sensor Charging Cradle and Power Supply REDMIKE® Classroom Microphone Optional LT-71 LightMic... -
Page 8: Front Panel Controls
1. POWER Switch/POWER Indicator: flash green when audio (voice) This switch is used to turn the from the microphone is detected. 800iX ON (switch up), or OFF (switch down). When the POWER Controls the volume 4. A VOLUME: switch is in the ON position, the level of the teacher microphone POWER light will glow red. -
Page 9: Rear Panel Controls
This 1/4” unbalanced 3. AUDIO OUTPUT: Connect additional sensors to the audio output jack may be connected 800iX to cover large or odd-shaped to a “line in” jack on a mixer/amplifier. classrooms. This output is a mixed audio of channels A and B. -
Page 10: Redmike Controls And Connections
The battery should These contacts CHARgER CONTACTS (+ -): only be replaced by a Lightspeed interface with the charging tabs in the BC- AA rechargeable sensing battery RMCC cradle charger for daily charging. -
Page 11: Cradle Charger Controls And Connections
5, item 4.) A blinking Green LED means a non- Lightspeed battery has been installed (possibly an alkaline battery). Helpful Hint International Note: Appropriate power cord and adaptor are provided with all Lightspeed equipment. 800iX User Manual | 6... -
Page 12: Section 2: Installation
8 0 0 i X U s e r M a n u a l SECTION 2 Installation 7 | 800iX User Manual... -
Page 13: Unpacking Your System
8 0 0 i X U s e r M a n u a l 1. UNPACKING YOUR SYSTEM Ensure that you have received all of the components of your system. 800iX Infrared Receiver/Amplifier and Power Supply REDMIKE® SR-70F Infrared Sensor and cable... -
Page 14: Location Of The Receiver/Amplifier
8 0 0 i X U s e r M a n u a l 2. LOCATION OF THE RECEIVER • Before running wires to the 800iX • A good location would be on any or plugging in, find a suitable, stable bookcase or shelf within stable location for the amplifier. -
Page 15: Ir Sensor Installation
8 0 0 i X U s e r M a n u a l 3. IR SENSOR INSTALLATION Sensor location is very important for optimum performance of the 800iX Classroom Audio System. • BEST: On the ceiling at or near the middle of the classroom. -
Page 16: Suspended Ceiling Mount
Helpful Hint Use conduit to protect wires. • Conduit is the best means to keep the wires/ cables out of sight and safe from wear. (Conduit is not included.) 11 | 800iX User Manual... - Page 17 1. Ensure the power switch is in the “OFF” position and all front panel volume controls are turned fully counter-clockwise. 2. Locate the 1/4”– 1/4” mono cable. 3. Connect the cable from the 1/4” audio output jack on the 800iX to the input jack on the 880iR, 850iR, or an existing amplifier. 850iR Receiver/...
-
Page 18: Audio Integration
5. AUDIO INTEGRATION 800iX BLOCK DIAGRAM Video In Projector Projector IR Sensor IR Transmission Teacher’s Microphone Audio Out VGA Out Speaker(s) Video Out Audio Out 800iX Audio Out Video Out Audio In DVD/VCR Existing Amplifier 800iX User Manual | 13... -
Page 19: Finalizing Connections
2. The amplifier packing material should be kept for warranty shipping purposes. 3. Proceed to initial set-up to test system performance. Leave microphones charging so they are ready for use. Microphones will need to be charged on a daily basis. 800iX User Manual | 14... -
Page 20: Section 3: Initial Set-Up, Charging And Additional Features
8 0 0 i X U s e r M a n u a l SECTION 3 Initial Set-up, Charging and Additional Features 15 | 800iX User Manual... -
Page 21: Initial Set-Up Of Redmike
ON position. The RED LED on the switch will glow. 2. Turn on the REDMIKE. The RED IR LED on the 800iX will light to indicate a signal is being received. 3. Slip the REDMIKE with lanyard around the neck and position the top of the microphone just below the collarbone. -
Page 22: Charging The Redmike
• REDMIKE incorporates alkaline protection into the microphone design. Replacement AA NiMH batteries may only be purchased through Lightspeed Technologies (part # BA-NH2A27). • A blinking LED indicates a charging error. Be sure to use a Lightspeed rechargeable sensing battery. 17 | 800iX User Manual... -
Page 23: Using The Redmike To Amplify External Audio Equipment
CH A does not have to be adjusted. It’s easy to REMEMBER: determine which REDMIKE is set to Channel B by speaking into the mic and watching which set of LED’s glow on the front panel of the 800iX. AUDIO your laptop, MP3 2. Plug... -
Page 24: Section 4: Optional Microphones And Accessories
8 0 0 i X U s e r M a n u a l SECTION 4 Optional Microphones and Accessories 19 | 800iX User Manual... -
Page 25: Optional Redmike Vc Controls And Connections
The battery should VOLUME CONTROLS (UP - DOWN): Adjusts only be replaced by a Lightspeed microphone volume by pressing the up AA rechargeable sensing battery or down arrow buttons on the back of the (part # BA-NH2A27). -
Page 26: Initial Set-Up Of Optional Redmike Vc
Having the volume set too high will result in feedback and listener fatigue. NOTE: A nominal volume level must be set on the 800iX before adjusting controls on the REDMIKE VC. -
Page 27: Charging The Optional Redmike Vc
GREEN. Helpful Hint • REDMIKE VC incorporates alkaline protection into the microphone design. Replacement AA NiMH batteries may only be purchased through Lightspeed Technologies (part # BA-NH2A27). • A blinking LED indicates a charging or sensing error (see page 7.) Be sure to use a Lightspeed rechargeable sensing battery. -
Page 28: Optional Lt-71 Controls And Connections
BLUE when the LT-71 glow RED to indicate charging. is powered ON, RED when being charged. External Microphone Input (MIC): Use the 3.5mm MIC jack for the optional TK-250 headset microphone (part# MC-TK250LTM). 23 | 800iX User Manual... -
Page 29: Initial Set-Up Of Optional
8 0 0 i X U s e r M a n u a l INITIAL SET-UP OF OPTIONAL LT-71 1. Turn the 800iX power switch to the ON position. The RED LED on the switch will glow. 2. Turn on the LT-71 and set the operating channel to “B”. -
Page 30: Charging The Optional
Microphones can be left in the charger for up to two weeks without degradation to battery life. • A full charge will be attained in 8-10 hours. • Fully charged Lightspeed microphones will last over 7 hours. 800iX User Manual | 25... -
Page 31: Optional Hm-70 Controls And Connections
Power/Charge Indicator: adjustment should be necessary. light glows RED when the HM-70 is powered ON, GREEN when charging. Plug Charger Input (CHARGER): the charging cable from the charger into this jack for daily charging. 800iX User Manual | 26... -
Page 32: Initial Set-Up Of Optional Hm-70
8 0 0 i X U s e r M a n u a l INITIAL SET-UP OF OPTIONAL HM-70 1. Ensure the 800iX is ON. The RED LED on the power switch will glow. 2. Turn on the HM-70 by sliding the switch to the top position. -
Page 33: Charging The Optional
(8–10 hrs.) to obtain a full charge. The GREEN light will turn off when fully charged. NOTE: If the system was purchased without a REDMIKE or REDMIKE VC, the HM-70 will utilize the charger jacks on the back of the 800iX. AUDIO OUTPUT DC POWER BALANCED... -
Page 34: Audio Integration For The Optional Ir Media Connector
Existing Amplifier iR Media Connector Audio Out Video Out DVD/VCR 800iX The iRMC is designed to integrate with the 800iX and multiple audio sources, allowing other instructional technologies to be clearly heard throughout the classroom. 29 | 800iX User Manual... -
Page 35: Intial Set-Up Of Optional Ir Media Connector
3. If the first two options do not give optimum volume level, the last place to adjust the volume is the CH. B Volume on the 800iX. Helpful Hint If you adjust the CH B volume on the classroom audio system, you will also be changing the volume for your second microphone. -
Page 36: Section 5: Troubleshooting, Daily Use And Warranty
8 0 0 i X U s e r M a n u a l SECTION 4 Troubleshooting, Daily Use and Warranty 31 | 800iX User Manual... -
Page 37: Troubleshooting Guide
Channel A. If you review these instructions and still have questions, write down the serial number and model number of your system and call Lightspeed Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST. -
Page 38: Daily Use Instructions
8 0 0 i X U s e r M a n u a l DAILY USE INSTRUCTIONS 1. TURN ON THE 800iX the power is switched on. Ensure 2. POSITION THE REDMIKE the REDMIKE from the Remove charging cradle and place it around your neck. -
Page 39: Tips On Classroom Audio
4. Warranty does not extend to finish, appearance items, or malfunctions due to abuse or operation other than specified conditions, nor does it extend to incidental or consequential damages. Repair by other than Lightspeed or its authorized service agencies will void this guarantee. Information on authorized service agencies is available from Lightspeed Technologies, Inc. -
Page 40: System Specifications
Weight ..............7.36 oz. IR SENSOR SPECIFICATIONS Working Range ............. Up to 1600 square feet per sensor Cable ..............50 ft., Plenum-rated Mounting .............. Ceiling clip/Wall bracket Dimensions ............4.25” (Diam.) x 2.0” (H) Weight ..............4.5 oz. 35 | 800iX User Manual... -
Page 41: Individual Components And Optional Accessories
8 0 0 i X U s e r M a n u a l INDIVIDUAL COMPONENTS & OPTIONAL ACCESSORIES Part Number Description RX-800 Infrared receiver/amplifier/mixer PS-16V-1.0 Power supply/battery charger for 800iX Infrared sensor with cable and wall or ceiling mounting IR-SR70F bracket CA-PC50F Plenum sensor cable (50 ft.) REDMIKE classroom microphone... -
Page 42: User Notes
USER NOTES Record your system serial numbers and purchase information. This is helpful when ordering additional components, accessories, and/or warranty service. Components Serial Number 800iX Microphones Sensors Speakers Purchase Information Your School/Organization District Purchase Date Invoice 37 | 800iX User Manual... - Page 43 8 0 0 i X U s e r M a n u a l USER NOTES 800iX User Manual | 38...
- Page 44 8 0 0 i X U s e r M a n u a l USER NOTES 800iX User Manual | 39...
- Page 45 8 0 0 i X U s e r M a n u a l USER NOTES 800iX User Manual | 40...
- Page 46 8 0 0 i X U s e r M a n u a l USER NOTES 800iX User Manual | 41...
- Page 48 AC-MN800 LI gHTSPE ED TE CHN O LOgIES 1 1509 S W HERMAN RO AD / T U AL ATI N, OR 9 706 2 TOL L F RE E: 800. 732. 89 99 / P H O NE: 5 03.68 4.55 38 / FAX: 50 3 .6 84 .31 9 7 LIGHTSPE ED-TEK .CO M MN0191US01-1...
Need help?
Do you have a question about the 800IX and is the answer not in the manual?
Questions and answers