Listening To Mpx Stereo; Listening To A Stereo Record; Listening To Monophonic Records; Listening To Tape Decks - McIntosh MX 110 Owner's Manual

(L+R)
3. Place the PHASE switch in the 0°
position.
4. Place the HF cutoff filter switch in the
OUT position. (See page 15 ADJUSTING FOR
SPECIAL EFFECTS.)
5. Place the LF rumble filter switch in the
OUT position. (See page 15 ADJUSTING
FOR SPECIAL EFFECTS.)
6. Place the LOUD switch in the OUT posi-
tion. (See page 15 ADJUSTING FOR SPE-
CIAL EFFECTS.)
7. Turn the BASS controls and TREBLE
controls so that the indicator is centered
between the panel markings • L and ° R.
(See page 15 BASS AND TREBLE CON-
TROLS.)
8. Place the MUTING switch in the IN
position.
9. Adjust the VOLUME control to the
desired volume.
After a warm up of about 30 seconds, turn
the tuning knob to find the station of your
choice.
While tuning the MX110 you may notice
that the tuning indicator will show a station
yet no program is heard from the speakers.
The muting circuit in the tuner is rejecting the
station because there is objectionable noise
with the weak signal from the station. Push
the MUTING switch to the OUT position and
the station will be heard. Most programs that
can be tuned in this manner are of poor
quality due to interfering noise.

LISTENING TO MPX STEREO

If you are tuning the MX110 and the red
MPX indicating light comes on, this indicates
a multiplex broadcast. To listen to this program:
1. Turn the INPUT SELECTOR to MPX.
2. Turn the MODE SELECTOR to STEREO.

LISTENING TO A STEREO RECORD

To listen to stereo records, proceed as
follows:
1. Turn the INPUT SELECTOR to PHONO
1 or PHONO 2, whichever is connected to
the cartridge you wish to hear.
2. Set the MODE SELECTOR to STEREO.
3. Set the PHASE switch to 0°.
4. Set the HF cutoff filter to OUT. (See
page 15 ADJUSTING FOR SPECIAL EFFECTS.)
16
5. Place the LF rumble filter control in the
OUT position. (See page 15 ADJUSTING
FOR SPECIAL EFFECTS.)
6. Set the LOUD control to OUT. (See
page 15 ADJUSTING FOR SPECIAL EFFECTS.)
7. Set the BASS controls and TREBLE
controls so that the indicator is centered
between the panel markings • L and ° R.
(See page 15 BASS AND TREBLE CON-
TROLS.)
8. Adjust the VOLUME control to the
desired volume.

LISTENING TO MONOPHONIC RECORDS

To listen to monophonic records, proceed
as follows:
1. Turn the INPUT SELECTOR to PHONO
1 or PHONO 2 whichever is connected to the
cartridge you wish to hear.
2. Set the MODE SELECTOR to MONO
(L+R).
3. Set the PHASE switch to 0°.
4. Set the HF cutoff filter to OUT. (See
page 00 ADJUSTING FOR SPECIAL EFFECTS.)
5. Place the LF rumble filter control in the
OUT position. (See page 15 ADJUSTING
FOR SPECIAL EFFECTS.)
6. Set the LOUD control to OUT. (See page
00 ADJUSTING FOR SPECIAL EFFECTS.)
7. Set the BASS controls and TREBLE
controls so that the indicator is centered
between the panel markings • L and ° R.
(See page 15 BASS AND TREBLE CONTROLS.)
8. Adjust the VOLUME control to the
desired volume.

LISTENING TO TAPE DECKS

To listen to tape from a tape deck, pro-
ceed as follows:
1. Turn the INPUT SELECTOR to TAPE
HEAD.
2. Set the MODE SELECTOR to MONO
(L+R) or STEREO, depending on the pro-
gram on the tape.
3. Set the PHASE switch to 0°.
4. Set the HF cutoff filter to OUT. (See
page 15 ADJUSTING FOR SPECIAL EFFECTS.)
5. Place the LF rumble filter control in
the OUT position. (See page 15 ADJUSTING
FOR SPECIAL EFFECTS.)
6. Set the LOUD control to OUT. (See page
15 ADJUSTING FOR SPECIAL EFFECTS.)