Audio Setup; Radio Operations - Clarion M502 Owner's Manual & Installation Manual

System Setup
S-CTRL (iPod mode) : ON/OFF
Rotate the [CONTROL] knob to choose S-CTRL
(Simple control) ON or OFF.
* Refer to P12.
RESET
1. Select "RESET".
2. Press and hold the [CONTROL] knob to
reset.
3. Settings will be set to the default value.
4. The unit will be turned off automatically.
Note:
• When the [RESET] is selected and you
press and hold the [CONTROL] knob, radio
station frequencies, titles, and other data
stored in memory are cleared.

Audio Setup

SOUND
Press the [CONTROL] knob to choose
SOUND. First press shows current EQ. Rotate
the [CONTROL] knob to choose BEAT EQ in
this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
To change CUSTOM setting, and press
the [CONTROL] knob (center), then press
[CONTROL] knob (right/left) to select EQ
effects including: BASS-G -> BASS-F ->
BASS-Q -> MID-G -> MID-F -> MID-Q
-> TREBLE-G -> TREBLE-F, rotate the
[CONTROL] knob to select a value.
BASS-G / MID-G / TREBLE-G: (-7)- (+7)
BASS-F: 50 / 100 / 200
BASS-Q : 0.7 / 1.0 / 1.4 / 2.0
MID-F: 500 / 1 K / 2 K
8
M502
MID-Q: 0.7 / 1.0 / 1.4 / 2.0
TREBLE-F: 5 K / 10 K / 15 K
TREBLE-Q: 0.7 / 1.0 / 1.4 / 2.0
Then press the [CONTROL] knob (left / right) to
select USER preset including:
BALANCE -> FADER -> M-B EX ->HPF(high
pass filter) -> LPF(low pass filter) -> S-W VOL
(Subwoofer Volume), rotate the [CONTROL]
knob to select a value.
BALANCE:LEFT 1-7->CENTER->RIGHT 1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-B EX: ON/OFF
HPF: THROUGH/60/90/120
LPF: THROUGH/60/90/120
SUBW VOL: (-6)-(+6)

Radio Operations

Select tuner as playing source
Press the [CONTROL] knob or [SRC / ]
button on the remote control to switch to the
RADIO source.
Select one radio band
Press the the [CONTROL] knob (up long
press) on the panel or [BAND/TOP] button
on the remote control to select one radio
band among FM1, FM2, FM3 and AM.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press [CONTROL] knob (left/right) on the
panel or [ , ] buttons on the remote
control to tune in a higher / lower station.
Auto tuning
Press and hold [CONTROL] knob (left/right)
on the panel or [ , ] buttons the remote
control to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
useful when searching for a desired station
in memory.
1. Press the [SCN/PS/AS] button on the
remote control.
2. When a desired station is tuned in, press
the [SCN/PS/AS] button on the remote
controlagain to continue receiving that
station.
Note:
Be careful not to press and hold the
[SCN/PS/AS] button, otherwise the auto
store function is engaged and the unit starts
storing stations.
Auto store
Only stations with sufficient signal strength will be
detected and stored in the memory.
Press and hold the [SCN/PS/AS] button on the
remote control to start automatic station search.
To stop auto store, press other buttons having
radio functions.
Notes:
1. After auto store, the previous stored stations
will be overwritten.
2. The unit has 4 bands, such as FM1, FM2,
FM3 and AM. FM3 and AM can store by AS
function. Each bands can store 6 stations,
M502 can store 24 stations in total.
Manual store
When one expected radio station has been
detected, press and hold number button on the
remote control 1-6 to store it in the memory.
Recall the stored stations
Press one numeric button among 1 to 6 on the
remote control or on the panel to select the
corresponding stored station.
Local seeking
When LOCAL seeking is on, only those radio
stations with strong radio signal could be
received.
Refer to System Setup page 7.
Note:
The number of radio stations that can be received
will decrease after the local seeking mode is on.