Table of Contents
Advertisement
Operation
Basic Operation
Once you have completed the setup and configu-
ration of the AVR 3550, it is simple to operate
and enjoy. The following instructions should be
followed for you to maximize your enjoyment of
your new receiver:
Turning the AVR On or Off
• When using the AVR for the first time, you must
press the Main Power Switch
panel to turn the unit on. This places the unit in a
Standby mode, as indicated by the orange color of
the Power Indicator
. Once the unit is in
Standby, you may begin a listening session by
pressing the System Power Control
Source button
on the front panel or the AVR
Selector
. Note that the Power Indicator
will turn green. This will turn the unit on and
return it to the input source that was last used.
The unit may also be turned on from Standby by
pressing any of the Source Selector buttons on
the remote
.
NOTE: After pressing one of the Input Selector
buttons
to turn the unit on, press the AVR
Selector
to have the remote control the AVR
functions.
To turn the unit off at the end of a listening ses-
sion, simply press the System Power Control
on the front panel or the Power Off
Button
on the remote. Power will be shut
off to any equipment plugged into the rear panel
Switched AC Outlets
and the Power
Indicator
will turn orange.
When the remote is used to turn the unit "off" it
is actually placing the system in a Standby mode,
as indicated by the orange color of the Power
Indicator
.
When you will be away from home for an
extended period of time it is always a good idea
to completely turn the unit off with the front
panel Main Power Switch
.
NOTE: All preset memories may be lost if the
unit is left turned off with the Main Power
Switch
for more than two weeks.
Using the Sleep Timer
• To program the AVR for automatic turn-off,
press the Sleep Button
on the remote. Each
press of the button will increase the time before
shut down in the following sequence:
90
80
70
60
50
min
min
min
min
min
40
30
20
10
OFF
min
min
min
min
The sleep time will be displayed in the Preset
Number/Sleep Timer Indicator
count down until the time has elapsed.
When the programmed sleep time has elapsed,
the unit will automatically turn off (to Standby
mode). Note that the front panel display will dim
to one half brightness when the Sleep function
is programmed. To cancel the Sleep function,
press and hold the Sleep Button
on the front
information display returns to normal brightness
and the Sleep indicator numbers return to "0" in
the Main Information Display
Source Selection
or the
• To select a source, press any of the Source
Selector buttons on the remote
NOTE: After pressing one of the Input Selector
buttons
you must press the AVR Selector
to have the remote control the AVR functions.
• The input source may also be changed by
pressing the front-panel Input Source
Selector button
will move the input selection through the list of
available inputs.
• As the input is changed, the AVR 3550 will
automatically switch to the digital input (if
selected) and surround mode that were entered
during the configuration process for that source.
• As the input source is changed, the new input
name will appear momentarily as an on-screen
display in the lower third of the video display.
The input name will also appear in the Main
Information Display
light next to the selected input's name in the
front-panel Input Indicators
• When a pure audio source (Tuner, CD, Tape, 6
Channel direct inputs) is selected, the last video
input used remains routed to the Video 1
Output
and Video Monitor Output
This permits simultaneous viewing and listening
to different sources.
• When a Video source is selected, its audio sig-
nal will be fed to the speakers and the video sig-
nal for that input will be routed to the appropriate
Monitor Output jack
on a TV monitor connected to the AVR.
Controls and Use of Headphones
and it will
• Adjust the volume to a comfortable level using
the front panel Volume Control
Volume Up/Down
• The Balance Control
adjust the relative sound output between the left
front and right front speakers.
until the
• To temporarily silence all speaker outputs
press the Mute button
the output to all speakers and the headphone
.
jack, but it will not affect any recording or dub-
bing that may be in progress. Press the Mute
button
• During a listening session you may wish to
.
adjust the Bass Control
Control
acoustics. Note that these controls are not effec-
tive with the 6-Channel Direct Input.
• To set the output of the AVR so that the out-
put is "flat", with the Tone controls and the
Balance control de-activated, press the Tone
. Each press of the button
Mode button
the words T o n e O u t appear momentarily
in the Main Information Display
return the tone controls to an active condition,
press the Tone Mode
so that the words T o n e I n momentarily
appear in the Main Information Display
• For private listening, plug the 6.3 mm stereo
phone plug from a pair of stereo headphones
into the front panel Headphone Jack
that when the headphone's plug is connected,
and a green LED will
the word HEADPHONE will scroll once
across the Main Information Display
.
all speakers will be silenced. When the head-
phone plug is removed, the audio feed to the
speakers will be restored.
.
and will be viewable
or remote
buttons.
may be used to
. This will interrupt
again to return to normal operation.
and Treble
to suit your listening tastes or room
button once or twice so that
. To
button once or twice
. Note
and
OPERATION 25
.
Hide quick links:
Advertisement
Table of Contents
