Table of Contents
Advertisement
Programming the Remote
Channel Control Punch-Through
The AVR's remote may be programmed to oper-
ate so that the channel control function for either
the TV, cable or satellite receiver used in your sys-
tem may be used in conjunction with one of the
other devices controlled by the remote. For exam-
ple, while using and controlling the VCR, you
may wish to change channels on a cable box or
satellite receiver without having to change the
device selected by the AVR or the remote. To pro-
gram the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector button
device you wish to have the channel control asso-
ciated with and the Mute button
same time until the red light illuminates under the
Input Selector
and the Program/SPL
Indicator
flashes amber.
2. Press the Volume Down button
Program/SPL Indicator
will stop flashing
and stay amber.
3. Press and release the AVR
or Input
Selector button
for the device that will be
used to change the channels. The Program/SPL
Indicator
will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
and the Mute button
at the same time. Next,
release them and press the Volume Down but-
ton
, followed by the VID 2/TV Input
Selector button
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 1/VCR Input
Selector in Steps 1 and 3.
Transport Control Punch-Through
The AVR's remote may be programmed to oper-
ate so that the Transport Control Functions
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in
conjunction with one of the other devices con-
trolled by the remote. For example, while using
and controlling the TV, you may wish to start or
stop your VCR or DVD without having to change
the device selected by the AVR or the remote. To
program the remote for Transport Control Punch-
Through, follow these steps:
for the
1. Press the Input Selector
you wish to have the channel control associated
at the
with and the Mute button
until the red light illuminates, under the Input
Selector
and the Program/SPL Indicator
flashes amber.
. The
2. Press the Play button
Indicator
will stop flashing and stay amber.
3. Press and release the AVR
Selector button
used to change the channels. The Program/SPL
Indicator
will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
Mute button
at the same time. Next, release
them and press the Play button
the CD Input Selector button
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 2/TV Input
Selector in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
Resetting the Remote Memory
As you add components to your home-theater
system, occasionally you may wish to totally
reprogram the remote control without the con-
fusion of any commands, macros or "Punch-
Through" programming that you may have done.
To do this, it is possible to reset the remote to
the original factory defaults and command codes
by following these steps. Note, however, that
once the remote is reset, all commands or codes
that you have entered will be erased and will
need to be re-entered:
for the device
1. Press any of the Input Selector buttons
and the "O" button
at the same time
the Program/SPL Indicator
amber.
2. Press the "3" button
3. The red LED under the Input Selector
. The Program/SPL
go out and the Program/SPL Indicator
stop flashing and turn green.
or Input
4. The Program/SPL Indicator
for the device that will be
green until the remote is reset. Note that this may
take a while, depending on how many commands
are in the memory and need to be erased.
5. When the Program/SPL Indicator
out, the remote has been reset to the factory
settings.
and the
, followed by
.
at the same time until
begins to flash
three times.
will
will
will remain
goes
PROGRAMMING THE REMOTE 37
Hide quick links:
Advertisement
Table of Contents
