CHIEF MFC Series Installation Instructions Manual
Display carts
Hide thumbs
Also See for MFC Series:
- Installation instructions manual (10 pages) ,
- Installation instructions manual (12 pages) ,
- Installation instructions manual (12 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for CHIEF MFC Series
Summary of Contents for CHIEF MFC Series
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Display Carts MFC, PFC Series...
-
Page 2: Important Warnings And Cautions
Chief® and ClickConnect™ are registered trademarks of Reinforce the structure as required before installing the Milestone AV Technologies. All rights reserved. - Page 3 MFC, PFC Series Installation Instructions DIMENSIONS...
- Page 4 Installation Instructions MFC, PFC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
-
Page 5: Tools Required For Installation
Installation Instructions MFC, PFC Series TOOLS REQUIRED FOR INSTALLATION 3/16" (Included) PARTS B (1) [right leg] A (1) [left leg] D (4) [snap-on cover] E (1) C (2) [center post] [end cap] F (1) [cross bracket] G (1) J (1) PFC Head 3/16"... - Page 6 MFC, PFC Series Installation Instructions ASSEMBLY inner column CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit (J) and power drill to complete the attachment.
- Page 7 Installation Instructions MFC, PFC Series IMPORTANT ! : When attaching head assembly ensure that the ClickConnect lock is at TOP of head assembly, and bracket tabs slide into the stand assembly. (See Figure 5) Slide head assembly (G) or (H) into the stand assembly. (See Figure 5) Attach head assembly (G) or (H) to the cart assembly using four 5/16-18 x 3/4"...
- Page 8 MFC, PFC Series Installation Instructions Attaching Display to Cart WARNING: IMPROPER INSTALLATION CAN LEAD TO CART OR DISPLAY FALLING CAUSING SERIOUS WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY PERSONAL INJURY OR DAMAGE TO EQUIPMENT! MAY LEAD TO SERIOUS PERSONAL INJURY OR Ensure mounting buttons are completely engaged in DAMAGE TO EQUIPMENT! It is the installer’s responsibility mounting holes.
- Page 9 Installation Instructions MFC, PFC Series Tilting Display (Rear The display can be tilted up to 15 either backward or forward (Front view view of from a straight upright position. center post) of center post) Turn knob counterclockwise on back of head assembly to loosen the tilt.
- Page 10 MFC, PFC Series Installation Instructions Cart Use and Maintenance CAUTION: This cart is intended for use only with the products and maximum weights indicated (125 lbs [56.70 kg] for the MFC, and 200 lbs [90.72 kg] for the PFC). Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury.
- Page 11 Installation Instructions MFC, PFC Series Removing Display from Cart Remove bolt or padlock from faceplate (if used). (See Figure 15) NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes.
- Page 12 A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a products division P +31 (0)40 2668620 of Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Office No.
Need help?
Do you have a question about the MFC Series and is the answer not in the manual?
Questions and answers