Receiving A Private Call (All Types); Telephone Calls; General; Placing A Telephone Call - E.F. Johnson Company 5300 SERIES Operating Manual

6.5.4 RECEIVING A PRIVATE CALL (ALL
TYPES)
1. When a private call or unit call is received, "CALL
RCVD" is displayed and the call tone sounds once.
2. To answer the call, press the CALL (Private/Unit
Call) option switch and then the PTT switch and
begin speaking. The unit ID of the calling mobile is
displayed. More information follows:
•
If the PTT switch is pressed before the CALL
switch, the call is transmitted as a group call.
•
If private calls are not permitted (CALL switch not
programmed) press the RESP (Call Response)
option switch to respond.
•
The call must be answered within 20 seconds or it
is automatically terminated.
•
If the system is busy when a response is made,
"BUSY" is displayed and the busy tone sounds.

6.6 TELEPHONE CALLS

NOTE: In the P25 trunked mode, telephone calls are
available only with firmware Version 1.28/2.6/3.6/4.2
or later.

6.6.1 GENERAL

The telephone call feature* allows telephone calls
to be placed and received over the public telephone
system using your radio. The type of call (secure/
clear) is determined by the mode selected by the C/S
(Clear/Secure) option switch. Telephone calling is
programmed to operate in one of the following modes:
•
Disabled (telephone calls not available)
•
Answer-only capability
•
List only - Telephone numbers can be selected
from a preprogrammed list only (direct entry as
follows is not allowed)
•
Unlimited - Telephone numbers can be selected
from a list and also dialed directly** entered
using the front panel controls or the HHC keypad
(later units only).
* This feature requires firmware Version 1.20.0/2.0/3.0/
4.2 or later.
SMARTNET/SMARTZONE/P25 TRUNKED FEATURES

6.6.2 PLACING A TELEPHONE CALL

Recalling From A List
1. With a SMARTNET/SmartZone channel selected,
momentarily press the PHONE option switch. The
tag (alias) of the last called telephone number is
displayed.
2. If required, rotate the Select switch to display the
desired number. The tag of each number is
displayed.
3. Press and then release the PTT switch and
"DIALING" is displayed. Refer to the bulleted list
following step 6 in the next section for events that
may then occur.
Direct Entry Using DTMF Keypad
4. Press and hold the PHONE option switch until a
tone sounds (approximately 1 second). The alias of
the last called telephone number is displayed if it is
in the phone number list. Otherwise, the last ten
digits of the last called telephone number are
displayed. The phone call mode is indicated by
in the display.
5. If using the front panel controls, enter the telephone
number by rotating and pressing the Select switch.
*
The 0-9, the , #, and P (pause) characters can be
entered (# is displayed as a "+"). Numbers up to
sixteen digits (including pauses) can be entered, and
the number scrolls to the left in the display so that
the ten right-most digits are always displayed. With
the HHC, enter the number using the DTMF keypad
(a pause indicated by "P" is entered by
6. Press and release the PTT switch and "DIALING" is
displayed. Events that may occur are as follows:
•
If the access is successful, a dial tone sounds and
the dialed number is displayed and sent. Either
ringing or a busy signal is then heard as with a
standard telephone call. When the called party
answers, press the PTT switch to talk and release it
to listen (since the radio operates half-duplex, it is
not possible to talk and listen at the same time).
** This feature requires firmware Version 1.28/2.6/3.6/4.2
or later.
43
*
#).