Table Of Contents; Introduction; Replacement Parts; Safety Instructions - Goodman AEPT Installation And Operating Instructions Manual

INDEX
INTRODUCTION .................................................................... 2
REPLACEMENT PARTS ........................................................ 2
SAFETY INSTRUCTIONS ...................................................... 2
WARNINGS ............................................................................ 2
MODEL IDENTIFICATION ...................................................... 3
PRODUCT DESCRIPTION ..................................................... 3
UNIT INSPECTION ................................................................. 4
ELECTRIC HEAT .................................................................... 4
HKR INSTALLATION .............................................................. 5
LOCATION .............................................................................. 5
DUCTWORK ........................................................................... 5
ELECTRICAL SUPPLY WIRE AND MOP ............................... 5
REFRIGERANT LINES ........................................................... 6
AEPT MOTOR ORIENTATION ............................................... 8
CONVERSION TO DOWNFLOW ........................................... 8
CONVERSION TO HORIZONTAL .......................................... 9
CONDENSATE REMOVAL ..................................................... 9
ACHIEVING 2% LOW LEAKAGE RATE .............................. 10
ARUF/ARPF MOTOR ........................................................... 10
AEPT MOTOR ....................................................................... 10
THERMOSTAT WIRING DIAGRAMS ................................... 11
THERMOSTATS .................................................................... 13

INTRODUCTION

Checking Product Received
Upon receiving the product, inspect it for damage from
shipment. Claims for damage, either shipping or concealed,
should be filed immediately with the shipping company.
Check the product to determine if it is correct. In the event
an incorrect product is shipped, it must be returned to the
supplier and must NOT be installed. The manufacturer
assumes no responsibility for installation of incorrectly
shipped products.
Before Beginning Installation
Carefully read all instructions for the installation prior to
installing product. Make sure each step or procedure is
understood and any special considerations are taken into
account before starting installation. Assemble all tools,
hardware and supplies needed to complete the installation.
Some items may need to be purchased locally. Make sure
everything needed to install the product is on hand before
starting.

REPLACEMENT PARTS

Ordering Parts
When reporting shortages or damages, or ordering repair
parts, give the complete product model and serial numbers
as stamped on the product. Replacement parts for this
product are available through your contractor or local
distributor. For the location of your nearest distributor
consult the white business pages, the yellow page section
of the local telephone book, or contact the following:
SERVICE PARTS DEPARTMENT
GOODMAN MANUFACTURING COMPANY, L.P.
2550 NORTH LOOP WEST, SUITE 400
HOUSTON, TEXAS 77092
(713) 861 - 2500
IO-230F
IMPORTANT SAFETY INSTRUCTIONS
Recognize Safety Symbols, Words, and Labels
The following symbols and labels are used throughout this
manual to indicate immediate or potential hazards. It is the
owner's responsibility to read and comply with all safety
information and instructions accompanying these symbols.
Failure to heed safety information increases the risk of
serious personal injury or death, property damage and/or
product damage.
DANGER
IMMEDIATE HAZARDS WHICH WILL RESULT IN
PROPERTY DAMAGE, PRODUCT DAMAGE, SEVERE
PERSONAL INJURY OR DEATH.
WARNING
HAZARDS OR UNSAFE PRACTICES COULD RESULT IN
PROPERTY DAMAGE, PRODUCT DAMAGE, SEVERE
PERSONAL INJURY OR DEATH.
CAUTION
HAZARDS OR UNSAFE PRACTICES WHICH MAY
RESULT IN PROPERTY DAMAGE, PRODUCT DAMAGE,
PERSONAL INJURY OR DEATH.
WARNING
THE UNIT MUST HAVE AN UNINTERRUPTED,
UNBROKEN ELECTRICAL GROUND TO MINIMIZE THE
POSSIBILITY OF PERSONAL INJURY IF AN ELECTRICAL
FAULT SHOULD OCCUR. THE ELECTRICAL GROUND
CIRCUIT MAY CONSIST OF AN APPROPRIATELY SIZED
ELECTRICAL WIRE CONNECTING THE GROUND LUG
IN THE UNIT CONTROL BOX TO THE BUILDING
ELECTRICAL SERVICE PANEL. OTHER METHODS OF
GROUNDING ARE PERMITTED IF PERFORMED IN
ACCORDANCE WITH THE "NATIONAL ELECTRIC CODE"
(NEC)/"AMERICAN NATIONAL STANDARDS INSTITUTE"
(ANSI)/"NATIONAL FIRE PROTECTION ASSOCIATION"
(NFPA) 70 AND LOCAL/STATE CODES. IN CANADA,
ELECTRICAL GROUNDING IS TO BE IN ACCORDANCE
WITH THE CANADIAN ELECTRIC CODE CSA C22.1.
FAILURE TO OBSERVE THIS WARNING CAN RESULT IN
ELECTRICAL SHOCK THAT CAN CAUSE PERSONAL
INJURY.
WARNING
BEFORE SERVICING OR INSTALLING THIS EQUIPMENT,
THE ELECTRICAL POWER TO THIS UNIT MUST BE IN
THE "OFF" POSITION. CAUTION, MORE THAN ONE
DISCONNECT MAY EXIST. FAILURE TO OBSERVE THIS
WARNING MAY RESULT IN AN ELECTRICAL SHOCK
THAT CAN CAUSE PERSONAL INJURY.
WARNING
DUE TO HIGH SYSTEM PRESSURE AND ELECTRICAL
SHOCK POTENTIAL, INSTALLING AND THE SERVICING
AIR CONDITIONING SYSTEMS CAN BE HAZARDOUS.
ONLY TRAINED AND QUALIFIED PERSONNEL ARE
PERMITTED TO INSTALL OR SERVICE THIS EQUIPMENT.
OBSERVE ALL WARNINGS CONTAINED IN THIS MANUAL
AND LABELS/TAGS ATTACHED TO THE EQUIPMENT.
2
08/04