Electrical Connection - AEG C9500G-CMI Instruction Booklet

XII
VI
ELECTRONIC TIMER FOR COOKER (Fig. 9)
Functions
On
The display flashes.
Time setting
Press the left button.
Set the time with buttons "+" and "-".
This function remains activated 7 seconds after the last +/-
operation.
Timer setting
This function is permanently activated and it will be immediately
set with +/- buttons.
During setting the units are 10 seconds.
During count down the timer takes priority on the display.
The units are seconds.
The maximum time is 99 minutes.
The relay contact (when available) is closed during the count down
only.
Reset timer
Press "+" and "-" buttons together and release "+" button first.
Signal
The signal after time out will stay 7 minutes if it has not been reset
with the "+" button (one touch only).
Signal frequency
When the display shows the time of day, the signal frequency can
be selected by pressing the "-" button. Three different frequencies
are selectable.
Fig. 9
1 Time of the day
2 Timing and insertion
3 Signal timng and insertion

ELECTRICAL CONNECTION

Connection of the appliance to the power mains should be done
by a licensed electrician familiar with local safety regulations.
GB
This appliance must be earthed by law. Before connecting
the appliance to the electrical supply, check that the earth
system in your house is working correctly.
Check that unit voltage and power, marked on the rating plate
applied on the appliance, are correct for the supply. It is necessary
that the feeding network is protected by a powerful switch able to
disconnect completely the network with a contacts separation of
at least 3 mm. Be sure that the earth wire green/yellow is not
interrupted by the switch.
Important: The wires in the mains lead are so coloured:
- green/yellow = earth " "
- blue = neutral "N"
- brown = live "L"
The wire coloured green/yellow must be connected to the terminal
in the plug which is marked with letter 'E' or by the earth symbol
or coloured green or green/yellow. The wire coloured blue must
be connected to the terminal which is marked with letter 'N' or
coloured black. The wire coloured brown must be connected to
the terminal which is marked with letter 'L' or coloured red. The
supply cable must not come into contact with any component the
temperature of which exceeds the ambient temperature by 50°C.
If a plug is used for connection, the plug to be connected to the
supply cable and the socket to which it is connected must be of
the same type (conforming to the standards). Easy access to the
plug or the switch is ensured once the appliance is installed. Ensure
that there is sufficient cable allowed for any subsequent removal
of the unit. If the plug is non-rewireable, pay attention to the
following points: the plug must never be cut by the supply cord.
There is shock hazard when this plug is inserted in a socket-outlet
elsewhere in the house. Never use the plug without the fuse cover
fitted. Referring to the pertinent spare parts, apply to the appliance's
supplier. The manufacturer declines all responsibility for any
damage to persons or things caused by failure to observe
the rules indicated above.
Applance type Supply single-phase 230 V~
Type of cable
Aii gas Rubber H05 RR-F
All gas + elett. grill Rubber H05 RR-F
REPLACEMENT OF THE CABLE
In case the cable is damaged, replace it in accordance with the
following instructions:
- open the box of the supply board as described on the picture
below;
- unscrew screw "A" fixing the cable;
- replace the cable with one of the same lenght and in accordance
with the features described on the table; switch the appliance
off, and close the gas tap
- the 'green-yellow" earth wire must be connected to the terminal
" " and it must be about 10 mm longer thean the live wires;
- the "blue" neutral wire must be connected to the terminal marked
with letter "N";
- the live wire must be connected to the terminal marked with letter
"L".
L
N
A
6
L
R
P
F
L
S
section
3 x 0,75 mm 2
3 x 2,5 mm 2
30
B
F
A
5
A
G
R L F
P
6
5
B
N
S
E
B
A
M
H
G
I
R
G