Related Manuals for GMC REDEYE DB305SMS
Summary of Contents for GMC REDEYE DB305SMS
-
Page 1: Instruction Manual
INSTRUCTION MANUAL Double Bevel Slide Compound Mitre Saw with Dual Laser Line Generator • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris DB250SMS DB305SMS 050805 ED05 PR... -
Page 2: Table Of Contents
Contents Description of symbols Specifications Safety rules for laser lights General safety instructions Additional safety rules for mitre saws Accessories Know your product Unpacking Transportation Bench mounting Stabiliser bar Release knob Slide lock Mitre table lock Bevel lock Bevel adjuster Clamp assembly Spindle lock button Rotating lower blade guard... -
Page 3: Description Of Symbols
Dear Customer If you require any help with your product, whether it is a Warranty claim, spare part or user information, please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. -
Page 4: Safety Rules For Laser Lights
Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the blade. To ensure safe operation of the mitre saw you must follow these guidelines – • Select the correct blade for the material to be cut. - Page 5 • The mitre saw can be safely carried by the main handle but only once it has been removed from the mains power and secured in the locked down position. • Do not use the saw without the guards in position, in good working order and properly maintained.
-
Page 6: Additional Safety Rules For Mitre Saws
• Ensure that there is adequate general or localised lighting. • Do not use the saw unless the guards are in place. • Do not use the saw to cut metal or masonry. • Do not let anyone under 18 years operate this saw. - Page 7 Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the machine is running and the saw head is not in the rest position. • Do not attempt to free a jammed blade before first switching off the machine.
-
Page 8: Accessories
Accessories The GMC DB250SMS / DB305SMS Double Bevel Slide Compound Mitre Saw is supplied with the following accessories as standard: • Saw blade (fitted) • Workpiece clamp • 6mm Hex key • Side bars x2 • Stabiliser Bar • Dust bag •... -
Page 9: Know Your Product
Know your product Before using the saw, familiarise yourself with all the operating features and safety requirements. 1. Laser light assembly 24. Switch trigger 2. Laser light on/off switch 25. Mitre lock 3. Laser cover 26. Spindle lock 4. Laser pitch control 27. -
Page 10: Unpacking
3. Using the carrying handle (8) carefully lift the saw from the carton and place it on a level work surface. 4. The saw has been shipped with the saw arm locked in the down position. To release the saw arm, push down on the top of the saw arm, pull on the release knob (6), rotate it 45°... -
Page 11: Slide Lock
0° bevel adjuster (18). Adjust the saw arm to the desired bevel angle. WARNING. a cut. Failure to do so could result in the saw arm moving during the cut and cause serious personal injury.0° Bevel adjuster The bevel adjuster (18) -
Page 12: Spindle Lock Button
(12) provides protection from both sides of the blade (fig. L). It retracts over the upper blade guard (9) as the saw is lowered into the workpiece. Dust bag The dust bag (15) fits over the dust extraction port (27). -
Page 13: Turning On And Off
9. The edge of the set square and the saw blade should be parallel. 10. If the saw blade angles away from the set square, adjust as follows. 11. Use a 13mm wrench or adjustable wrench to loosen the lock nut securing the 0°... -
Page 14: Setting The Fence Square With The Table
(35). Note. The above procedure can also be used to check the angle of the saw blade to the table at either 45º bevel angle to the left or to the right. The 45° bevel adjustment screws (33 & 34) are on opposite sides of the saw arm. -
Page 15: Changing A Blade
It will prevent the blade screw from properly securing the blade on the spindle. Do not use the saw to cut metal or masonry. Ensure that any spacers and spindle rings that may be required suit the spindle and the blade fitted. - Page 16 (fig p). 17. Check that the blade guard operates correctly and covers the blade as the saw arm is lowered. 18. Connect the saw to the power supply and run the blade to make certain that it is operating correctly.
-
Page 17: Cross-Cutting (Without Slide Action)
6. When cutting long pieces of timber, support the opposite end of the timber with the side support bars (37), a roller stand or a work surface that is level with the saw table. 7. Use the clamp assembly (10) to secure the workpiece wherever possible. -
Page 18: Cross-Cutting (With Slide Action)
0º and 45º (fig. u). Use the slide action when cutting wide workpieces. 1. Pull on the release knob (6) and lift the saw arm to its full height. 2. Loosen the mitre lock (25). 3. Rotate the mitre table (21) until the pointer aligns with zero on the mitre scale (22). -
Page 19: Compound Mitre Cut
Use the slide action when cutting wide workpieces. 1. Pull on the release knob (6) and lift the saw arm to its full height. 2. Loosen the mitre lock (25). -
Page 20: Using The Laser Line Generator
Switch off the laser light switch (2) and then remove the plug from the power point. • With the saw arm (5) in the raised position, use a soft brush to dust away the sawdust build-up around the assembly. NOTE. -
Page 21: Maintenance
4. Never use caustic agents to clean plastic parts. CAUTION. Do not use cleaning agents to clean the plastic parts of the saw. A mild detergent on a damp cloth is recommended. General inspection Regularly check that all the fixing screws are tight. - Page 24 Carefully read the entire Instruction Manual Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: •...