Subscribe to Our Youtube Channel
Related Manuals for GMC REDEYE CDB250MS
Summary of Contents for GMC REDEYE CDB250MS
-
Page 1: Instruction Manual
INSTRUCTION MANUAL Double Bevel Compound Mitre Saw with Dual Laser Line Generator CDB250MS • Melbourne • Perth • Auckland • Hong Kong • Shanghai CDB305MS • Taipei • New York • Verona • London • Paris 050804 ED2 PR... -
Page 2: Table Of Contents
It also does not cover any bonus accessories unless the We reserve the right to reject any claim where the Attaching the side bars tool is a GMC Platinum Professional model. purchase cannot be verified. Turning on and off Please ensure that you store your receipt in a safe place. -
Page 3: Dear Customer
It may be more difficult to see the laser line in Introduction conditions of bright sunshine and on certain surfaces. Your new GMC power tool will more than satisfy your Specifications expectations. It has been manufactured under stringent GMC Quality Standards to meet superior performance... -
Page 4: Safety Rules For Laser Lights
Safety rules for laser lights General safety instructions The laser light/laser radiation used in the GMC Redeye® To use this tool properly, you must observe the safety system is Class 2 with maximum 1mW and 400nm – regulations, the assembly instructions and the operating 700nm wavelengths. - Page 5 • The mitre saw can be safely carried by the main handle 3.Keep visitors away from the work area. All visitors but only once it has been removed from the mains and onlookers, especially children and infirm persons, power and secured in the locked down position. should be kept well away from where you are working.
-
Page 6: Additional Safety Rules For Mitre Saws
Additional safety rules for mitre saws 13. Disconnect idle tools. Switch off the power and disconnect the plug from the power point before WARNINGS. Before connecting a tool to a power source servicing, when changing accessories and when the (mains switch power point receptacle, outlet, etc.) be sure tool is not in use. - Page 7 • Never use your hands to remove sawdust, chips or waste that it is operated properly. As the operator of the close by the blade. saw, please make sure that you understand factors that influence exposure to dust, including the type •...
-
Page 8: Accessories
Accessories The GMC CDB250MS / CDB305MS Double Bevel Compound Mitre Saw is supplied with the following accessories as standard: • Saw blade (fitted) • Workpiece clamp • 6mm Hex key • Side bars x2 • Dust bag • Instruction manual •... -
Page 9: Know Your Product
Know your product Before using the saw, familiarise yourself with all the operating features and safety requirements. 1. Laser light assembly 21. Mitre table 2. Laser light on/off switch 22. Mitre scale 3. Laser cover 23. Table insert 4. Laser pitch control (kerf plate) 5. -
Page 10: Unpacking
Due to modern mass production techniques, it is unlikely 13mm or thicker plywood which can then be clamped that your GMC Power Tool is faulty or that a part is to your work support or moved to other job sites missing. -
Page 11: Bevel Adjuster
Spindle lock button the bevel lock and pull out the 0° bevel adjuster (18). The spindle lock button (26) Adjust the saw arm to the prevents the blade in the desired bevel angle. saw from rotating (fig. I). WARNING. Be sure to tighten Depress and hold the spindle the bevel lock before making lock button while installing,... -
Page 12: Turning On And Off
The side support bar 3. Loosen the mitre lock (25) locking screws (34) must (fig. P). be tightened to secure the 4. Rotate the table (21) until support bars in position the pointer is positioned (fig. M). at 0º. 5. Tighten the mitre lock (25). 6. -
Page 13: Setting The Fence Square With The Table
to bring the saw blade to hold the saw arm in the into alignment with the transport position. square (fig. T). 3. Loosen the mitre lock (25). 13. Loosen the 2 Phillips 4. Rotate the table (21) until the head screws holding the pointer is positioned at 0º. -
Page 14: Changing A Blade
Changing a blade guard (12) is positioned over the upper fixed blade DANGER! Never try to use a blade larger than the stated guard (9) it is possible capacity of the saw. It might come into contact with to access the blade bolt the blade guards. -
Page 15: Cross-Cutting
12. Replace the outer blade 1. Pull on the release knob (6) and lift the saw arm (5) to washer (fig. i). its full height. 13. Depress the spindle lock 2. Loosen the mitre lock (25). button (26) and replace 3. -
Page 16: Bevel Cut
blade to stop rotating 8. Use the clamp assembly (10) to secure the workpiece before raising the blade wherever possible. out of the workpiece. 9. It is possible to remove the clamp assembly (10) by Wait until the blade stops loosening the clamp assembly lock (11) and moving before removing the it to the other side of the table. -
Page 17: Adjusting The Laser Lines
adjuster (18) and move the saw arm (5) to the left or 2. Switch on the laser lights right to the desired bevel angle (between 0º and 45º). with the on/off switch (2) Tighten the bevel lock (16). (fig. q). 6. -
Page 18: Maintenance
Maintenance 3. Switch on the laser light on/off switch (2). 4. Clamp the workpiece in position using the laser lines to WARNING. Always ensure that the tool is switched off and align the blade with the pencil mark on the workpiece. the plug is removed from the power point before making and adjustments or maintenance procedures. - Page 20 • GMC Product Type • GMC Product Code A GMC Service Engineer will take your call and, in most cases, will be able to solve your problem over The GMC 777 Helpline operates from 7am to the phone. 7pm, 7 days a week (EST). This allows you...
Need help?
Do you have a question about the REDEYE CDB250MS and is the answer not in the manual?
Questions and answers
Can’t find a Manuel for Redeye workforce slide compound Miter Saw WfS814UL
The manual for the GMC Redeye CDB250MS slide compound miter saw is not specifically mentioned in the provided context. However, manuals for similar GMC Redeye models like LSMS250 and DB305SMS are available. You may refer to those for general guidance.
This answer is automatically generated