Philips Showline SL NITRO 510 Installation And User Manual page 29

SL NITRO 510 LED STROBE Luminaire
DMX
Parameter
Channel
1 Intensity - High Byte
2 Intensity - Low Byte
3 Strobe Effects
4 Control Channel
5 Zone 1 Intensity
6 Zone 1 Strobe Duration
7 Zone 1 Strobe Rate
8 Zone 2 Intensity
9 Zone 2 Strobe Duration
10 Zone 2 Strobe Rate
11 Zone 3 Intensity
12 Zone 3 Strobe Duration
13 Zone 3 Strobe Rate
Sh wline
Table 15: DMX Channel Mapping (Zone Mapping Mode)
Range DMX Range%
0 - 65535 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
Default - recom-
mended console Description
default values
16-bit control for the intensity of the LED settings
0
- 0 to 65535 (full)
Controls strobe operation as follows:
No Effect = DMX 0 - 5 (default)
Ramp Up = DMX 6 - 42
Ramp Down = DMX 43 - 85
Ramp up/down = DMX 86 - 128
Random = DMX 129 - 171
Top row only = DMX 172 - 173
0 Bottom row only = DMX 174 - 175
Left zone only = DMX 176 - 178
Center zone only = DMX 179 - 180
Right zone only = DMX 181 - 182
Checker pattern A = DMX 183 - 184
Checker pattern B = DMX 185 - 186
Random zones = DMX 187 - 214
Circle zone chase CW = DMX 215 - 235
Circle zone chase CCW = DMX 236 - 255
Control channel operation. Set control channel
value to desired action, hold value for at least 5
seconds, then turn to 0. Set control channel
value to 0 without any scaling.
Default Setting on Console = DMX 0-4
Dimming Curve_linear = DMX 30 - 34
Dimming Curve_Square = DMX 35- 39
Dimming Curve_S-Curve = DMX 40 - 44
Dimming Curve_PL-Curve = DMX 45 - 49
Fan_Auto = DMX 80 - 84
0
Fan_Off = DMX 85 - 89
The following is only for "Zones Mapping"
protocol. The following is instantly active and
does not require the 5 second hold:
Combined zone control-(all zones follow zone 1
setting) = DMX 100 - 104
Not Used = DMX 105 - 250 (Reserved for future
use)
0 8-bit control of Zone 1 intensity 0 to 255 (full)
Controls strobe duration for Zone 1. Refer to
"Strobe Duration DMX Timing
0
Detail" on page 30
Controls strobe rate for Zone 1. Refer to
"Strobe Rate DMX Timing Detail" on
0
page 29
.
0 8-bit control of Zone 2 intensity 0 to 255 (full)
Controls strobe duration for Zone 2. Refer to
"Strobe Duration DMX Timing
0
Detail" on page 30
Controls strobe rate for Zone 2. Refer to
"Strobe Rate DMX Timing Detail" on
0
page 29
.
0 8-bit control of Zone 3 intensity 0 to 255 (full)
Controls strobe duration for Zone 3. Refer to
"Strobe Duration DMX Timing
0
Detail" on page 30
Controls strobe rate for Zone 3. Refer to
"Strobe Rate DMX Timing Detail" on
0
page 29
.
Installation & User's Manual
.
.
Zone Mapping Mode
27