Page 1
8000C Digital Panoramic and Cephalometric System User’s Guide...
Page 2
Congratulations on your purchase of the KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System. The KODAK 8000C unit is the KODAK 8000 equipped with the cephalostat unit. Thank you for your confidence in our products and we will do all in our power to ensure your complete satisfaction.
Alerts you to a condition that might cause serious damage. IMPORTANT Alerts you to a condition that might cause problems. NOTE Emphasizes important information. Provides extra information and hints. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 1–1...
Page 6
Conventions in this Guide 1–2 About This Guide...
Chapter 2 KODAK 8000C UNIT OVERVIEW The KODAK 8000C digital panoramic and cephalometric unit is designed to carry out the following radiological examinations: • Panoramic • Maxillary Sinus • Temporomandibular Joints (TMJ) • Lateral cephalometric • Frontal (PA or AP) cephalometric •...
The Cephalostat can be positioned either on the right or the left side of the KODAK 8000 unit. Mobile Components Figure 2-1 illustrates the up and down movement of the KODAK 8000C digital panoramic and cephalometric units mobile component and the rotation of the rotative arm.
PC hosting the imaging and the acquisition software Hand Grips Cephalostat arm Control panel Cephalostat head Height adjustment buttons Head clamps and ear cones Panoramic digital sensor Nasion support X-Ray source assembly KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 2–3...
General Overview Digital Sensor Locations Figure 2-3 illustrates the locations of the digital panoramic and digital cephalometric sensors of the KODAK 8000C digital panoramic and cephalometric units. Figure 2–3 KODAK 8000 and KODAK 8000C Units Digital Sensor Locations system 2–4...
General Overview Laser Locations Figure 2-4 illustrates the location of the lasers of the KODAK 8000C digital panoramic and cephalometric units. Figure 2–4 KODAK 8000 and KODAK 8000C Units Laser Beam Locations Mid-sagittal plane positioning laser beam Frankfort plane positioning laser beam...
Display Screen: Displays the current acquisition parameters and the error messages. Reset button: Resets the unit arm to the initial position to enable the patient to enter and exit the unit. Laser beam button: Activates the laser positioning beams to correctly position the patient. 2–6 KODAK 8000C UNIT OVERVIEW...
You must press and hold the exposure button until the end of acquisition. Premature release of the exposure button interrupts the acquisition. Figure 2–6 X-Ray Remote Control Exposure button: launches image acquisition. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 2–7...
Positioning Accessories and Replacement Parts The following accessories are used when positioning a patient. They are delivered with the KODAK 8000 digital panoramic and KODAK 8000C digital panoramic and cephalometric unit. Table 2-1 and Table 2-2 list the panoramic and cephalometric positioning accessories.
Page 15
Positioning Accessories and Replacement Parts Table 2–2 Cephalometric Positioning Accessories and Replacement Parts Accessory Description Head clamps with ear cones Nasion support KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 2–9...
Page 16
Positioning Accessories and Replacement Parts 2–10 KODAK 8000C UNIT OVERVIEW...
Operating system (32 bits) Windows 2000 SP4 Windows XP Home / Pro • edition SP2 Windows XP Home / Pro • Windows Vista edition SP2 • Windows Vista 3–1 KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02...
Cephalometric acquisition interface module KODAK Dental Imaging Software The KODAK dental imaging software is a user-friendly working interface that was designed and developed specifically for radiological diagnosis. It is the common imaging platform for all our digital systems for dentistry.
X-Rays ON / OFF button: Turns off the x-ray emissions to demonstrate the acquisition process for the patient. Generator Cooling indicator: Indicates the automatic cooling time (mm:ss) required for the generator to reach 0 for a new acquisition. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 3–3...
Page 20
Cephalometric Acquisition Interface Module Positioning laser button: Activates the laser positionning beams to correctly position the patient. Reset button: Resets the rotative arm in the start position. Ready Indicator LED • Green indicates the unit is ready to start acquisition. •...
(AP and PA). Click for an oblique exam. NOTE The above list of exam types are only a sample of exam options of the Program pane. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 3–5...
Cephalometric Acquisition Interface Module Cephalometric Patient Pane The cephalometric Patient pane enables you to choose different patient parameters. The selection of the patient parameters influences the quality of the image. The selected parameters must be based on the patient age and morphology. Figure 3–3 Cephalometric Patient Pane Patient type parameters:...
Kilovolt mA: Milliampere S: Second Fine-tuning buttons: Click to fine-tune the kV, mA and the second. Saving parameter button: Click to save the selected parameters. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 3–7...
3. Leave the x-ray room and close the door. For each parameter setting, from the x-ray remote control, press and hold the button to launch the x-ray The unit is now ready to be used for acquisition. 4–1 KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02...
To start the imaging software, follow these steps: 1. On your desktop, double-click From your PC, click Start > All Programs > Kodak > Kodak Dental Software. A blank Patient Window is displayed. 2. Create or open an existing patient record.
To access the Acquisition Windows, follow these steps: 1. In the Imaging Window, from the toolbar, click to access the Cephalometric Acquisition Window. 2. Prepare the acquisition parameters and launch an acquisition. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 4–3...
Page 28
Accessing the Cephalometric Acquisition Window 4–4 GETTING STARTED...
Memorize settings. 7. Preparing and Positioning the Patient To prepare and position the patient, follow these steps: KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–1...
Page 30
Acquiring a Lateral Image 1. Ask the patient to remove all metal objects. 2. Ask the patient to wear a lead apron. Ensure that the apron lays flat across the patient’s shoulders. 3. Press and hold the height adjustment buttons to raise the cephalostat head. 4.
Page 31
Acquiring a Lateral Image 8. Lower the nasion support to a vertical position. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–3...
Page 32
Acquiring a Lateral Image Launching the X-ray To launch the x-ray, follow these steps: 1. Leave the x-ray room and close the door. You must keep visual contact with the patient during acquisition. IMPORTANT To stop the acquisition, if any problem, release the exposure button of the remote control or press the red emergency stop button.
Parameter button and in the Parameter pane select the appropriate parameters. To save the new parameter settings as the default settings, click fand select Memorize settings. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–5...
Acquiring a Frontal AP or PA Image Preparing and Positioning the Patient To prepare and position the patient, follow these steps: 1. Ask the patient to remove all metal objects. 2. Ask the patient to wear a lead apron. Ensure that the apron lays flat across the patient’s shoulders.
Page 35
IMPORTANT To stop the acquisition, if any problem, release the exposure button of the remote control or press the red emergency stop button. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–7...
Page 36
Acquiring a Frontal AP or PA Image Figure 5–5 Frontal AP Figure 5–6 Frontal PA 2. Launch the x-ray with the remote control. Press and hold the exposure button until the end of acquisition. The turns yellow indicating x-ray emission. The image appears on the Preview Screen of the Cephalometric Acquisition Window.
Parameter button and in the Parameter pane select the appropriate parameters. To save the new parameter settings as the default settings, click fand select Memorize settings. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–9...
Acquiring an Oblique Image Preparing and Positioning the Patient To prepare and position the patient, follow these steps: 1. Ask the patient to remove all metal objects. 2. Ask the patient to wear a lead apron. Ensure that the apron lays flat across the patient’s shoulders.
Page 39
Imaging Window. 3. Check the image quality. If satisfactory, remove the ear cones and the nasion support. Release the patient. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–11...
Acquiring a Submento-Vertex Image Acquiring a Submento-Vertex Image Before acquiring a submento-vertex image, check that you have: • Reset the unit rotative arm to the start position for patient to enter the unit. • Selected the patient record. • Accessed the Imaging Window. •...
6. Insert gently one cone in the auditory canal of the patient. Turn gently the button to close the arms. Insert gently the second cone in the auditory canal of the patient. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–13...
Page 42
Acquiring a Submento-Vertex Image Launching the X-ray To launch the x-ray, follow these steps: 1. Leave the x-ray room and close the door. You must keep visual contact with the patient during acquisition. IMPORTANT To stop the acquisition, if any problem, release the exposure button of the remote control or press the red emergency stop button.
Page 43
Cephalometric Acquisition Window disappears and the acquired image is automatically transferred to the Imaging Window. 3. Check the image quality. If satisfactory, remove the ear cones and release the patient. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–15...
Acquiring a Carpus Image Acquiring a Carpus Image Before acquiring a carpus image, check that you have: • Reset the unit rotative arm to the start position for patient to enter the unit. • Selected the patient record. • Accessed the Imaging Window. •...
4. Ask the patient to stand on the side of the cephalometric unit, open the hand fully and place it on the sensor. WARNING Make sure that the patient is not positioned in front of the x-ray emission. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–17...
Page 46
Acquiring a Carpus Image Launching the X-ray To launch the x-ray, follow these steps: 1. Leave the x-ray room and close the door. You must keep visual contact with the patient during acquisition. IMPORTANT To stop the acquisition, if any problem, release the exposure button of the remote control or press the red emergency stop button.
The radiation emission dose is expressed in mGy.cm2. This dose is measured at the primary collimator outlet. The dose is accurate to +/-30%. The primary slot is 0.5 mm wide and 18.2 mm high. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 5–19...
Page 48
X-Ray Dose Emission Information 5–20 ACQUIRING CEPHALOMETRIC IMAGES...
Wipe the outer covers of the unit with a soft, dry cloth. Annually We recommend a general inspection of the unit carried out by an authorized service technician. 6–1 KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02...
The exposure button of the x-ray position remote control is inactive Press to reset the rotative arm in start because the rotative arm is not in position. the start position. KODAK 8000C Digital Panoramic and Cephalometric Extraoral Imaging System User Guide (SM735)_Ed 02 7–1...
Page 52
Quick Troubleshooting Table 7–1 Information Messages (Continued) Information Error Code Information Message Description Action Raise sensor The panoramic sensor is Check that the panoramic sensor is fully incorrectly positioned. retracted and locked in the upper position. Lower sensor The panoramic sensor is Check that the panoramic sensor is fully incorrectly positioned.