Install The Receiver - Chamberlain MADCBB Owner's Manual

INSTALL THE RECEIVER »
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

INSTALL THE RECEIVER

WIRING THE RECEIVER
Contacts 1 and 2 on the receiver terminal strip are for power. The power terminals
are unpolarized. Connect terminals 1 and 2 to the accessory power terminals on the
J4 terminal strip at the bottom of the control board (Figure 1).
Contacts 3 and 4 on the receiver terminal strip are for a common and a relay.
Connect terminals 3 and 4 to terminals 1 and 10 on the J5 terminal strip at the top
of the control board.
NOTE: Auxiliary Pin 4 can be used for push to open/push to close functionality.
SET SECURITY MODE
The Universal Receiver can be used with up to 15 rolling code remotes or passwords
in HIGH security mode. Alternately, it can be used with up to 31 of any type remote
in NORMAL security mode, including any combination of rolling code, billion code
(390 MHz only), or dip switch remotes.
The jumper must be set at the HIGH position for the receiver to operate in HIGH
security mode. It must be set at NORMAL position to operate at the NORMAL mode
(Figure 2).
When changing from NORMAL to HIGH security mode, any previous remote codes
must be erased. Repeat Steps 2 and 3 in the Programming Section below to
reprogram the receiver for each remote control in use.
The receiver is factory set at HIGH.
PROGRAMMING THE REMOTE TO THE RECEIVER
Pry open the front panel of receiver case with a coin or a screwdriver.
1
Re-connect power to opener (Figure 3).
2
Press and release the "learn" button on the receiver. The learn indicator light
will glow steadily for 30 seconds.
3
Within 30 seconds, press and hold the button on the hand-held remote that
you wish to operate your gate.
The operator will now operate when the push button on either the receiver or the
remote control is pressed.
Repeat Steps 2 and 3 for each remote control that will be used to operate the gate.
TO ERASE ALL REMOTE CONTROL CODES
1
Press and hold the "learn" button on the receiver panel until the indicator light
turns off (about 6 seconds). All remote codes are now erased.
Follow the steps above to reprogram each remote control.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter
are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
INSTALL THE RECEIVER
FIGURE 1
UX LIMITS
2 3 4 5
R1Ø
R9
R8
R7
R6
R5
R4
R3
D9
D1
R2
Aux Relay
FIGURE 2
C NC NO
Security Mode Terminals
FIGURE 3
OPENING RECEIVER
12
MANUAL
1
J5
OPEN
Q2
M/S J3
R14
S3 T2
D1Ø
1 2 3 R18 4 5 6 7 8 9 1Ø 11 12
1 1 MANUAL
J2
OPEN J5 T1
Q2
AUX LIMITS M/S J3
R14
S3 T2 T4 T6 T8
D8 D1Ø R18
S2 T1 T3 R17 T5 T7
S1 S2 R17 OPEN 1 OPEN 2 OPEN 3
OPEN 1 OPEN 2 OPEN 3 AUX 4 SAFETY 5CLOSE 6 BACK 7SHADOW 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 CLOSE
R16 C16
6 7 8 R1 1 2 R12 3 4 5 6 7 8 R21
CLOSE
R24 R35 R41 R46 R5Ø R61
C3
R16
R12 U4 U8 U9 U11 U13 U14 U15 R21
C2
U1
R23 R34 R4Ø R45 R49 R6Ø
OLS
R24
D7
R22 R33 R39 R44 R48 C3 R59
OPEN R43
X1 R26 R43
R1Ø U6
D6
R63
D21
R9 U16
BRAKE IRD1 R25 R58 U8
U4
R8 C12
D5
U5 U12
U7 DX3
CLOSE
U1Ø
DX4
D4
C2 R7
CLS R57
D3 C13
R6 R56
IRD C4
DX2
D2 U3 CPU R38 R23
JP2
R5 U2
R37
R51
R19 F2 R55
R4 D2Ø
1A DC
R3 R2Ø C8 WARNING FOR
+ R62
Q1 C2Ø CONTINUOUS
F1
D9 C5 + PROTECTION
AGAINST FIRE DX1
D1 REPLACE ONLY R22
+ F4
WITH THE SAME
R2 R11 B1 TYPE AND RATING
HBEAT BAT LO AC POWER
OF FUSE
F3
K1
D11 D12 D14
X1
R26
R13
U19 J4 MOTOR
BAT– MOV U6
Aux Relay
TR
J1 C NC NO DC
1
1
PWR ACC+ ACC– BAT– BAT+ 24VAC XFMR MOTOR
IRD1
U5
U7
HBEAT BAT LO AC POWER
D11 D12 D14
R13
J4
U19
BAT–
C4
U3
CPU
1
JP2
U2
F2
R19
ACC+ ACC– BAT– BAT+
1A DC
R2Ø
+
F1
J4
J4
C5
+ F4
B1
R11
HBEAT BAT LO AC POWER
F3
K1
D11 D12 D14
–
+
R13
J4
U19
BAT– MOV
DC
1
Jumper
HIGH
SECURITY MODE
OPEN RECEIVER
Connect Antenna
24V 12V
J5
J5
1 2 3 4 5 6 7 8 9 1Ø 11 12
T4 T6 T8
T3 T5 T7
AUX 4 SAFETY 5CLOSE 6 BACK 7SHADOW 8
C16
R35 R41 R46 R5Ø R61
U9 U11 U13 U14 U15
R34 R4Ø R45 R49 R6Ø
R33 R39 R44 R48 R59
R43
R43
R63
D21
U16
R25
R58
C12
P1 to J4 Accessory Power
U12
DX3
U1Ø P2 to J4 Accessory Power
DX4
P3 to J5 Terminal 1
R57
C13
MOV
R56
P4 to J5 Terminal 10
DX2
R38
R37
R51
R55
D2Ø
C8 WARNING FOR
R62
C2Ø CONTINUOUS
+
PROTECTION
AGAINST FIRE
DX1
REPLACE ONLY
WITH THE SAME
10
TYPE AND RATING
1
OF FUSE
1
2
3
4
MOTOR
TR
P1-P4
Jumper
Security Mode Terminals
NORMAL
SECURITY MODE
Indicator Light
Learn Button
Output Duration
C
P2
Terminals
M
Security Mode
Power Supply Jumper
(Not Provided)