Introduction & Specifications - Dyna-Glo Series User Manual

Dyna-Glo ProPane ForceD air construction Heaters
The heater is designed and approved for use as a construction heater under anSi z83.7a, CSa 2.14a.
it is hard to anticipate every use which may be made of this heater.
FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.
other standards govern the use of fuel gases and heat producing products in specific applications.
your local authority can advise you about these.
IMPORTANT: read ThiS uSer'S Manual CareFully and CoMpleTely BeFore Trying
To operaTe or ServiCe ThiS heaTer. iMproper uSe oF ThiS heaTer Can CauSe
SeriouS injury or deaTh FroM Fire, exploSion and CarBon Monoxide poiSoning.
This is a direct-fired forced air construction heater for either indoor construction or outdoor use. its intended
use is primarily the temporary heating of buildings or structures under construction, alteration or repair. all the
products of combustion generated by the heater are forced through the heater and released into the area being
heated. This heater operates at approximately 98%+ combustion efficiency but still produces a small amount
of carbon monoxide. humans can tolerate small amounts of carbon monoxide for short periods. Carbon
monoxide can build up in a heated space and failure to provide adequate ventilation could result in poisoning
or death.
Model N o. RMC-­‐FA40
DG/DGD/
DGP/DGP-­‐01
Input R aFng 40,000 B TU/hr
Type o f G as Propane
Gas S upply P ressure
to R egulator Cylinder P ressure
Maximum
Minimum ( for
purpose o f I nput 5psig
Adjustment)
Manifold P ressure 11" W .C
Gas C onsumpFon 1.9lbs/hr
Electrical I nput 120V, 6 0Hz, 1 Ø
Amperage L oad 0.68amps
U nload 3550rpm
Fan
L oad 3000rpm
IgniFon Piezo/Manual S park ConMnuous S park
Spark G ap 0.16" ( 4mm)
19.3"x8.3"x15.2"
Size ( LxWxH)
(490x211x386)mm
13.7lbs/14lbs
Weight
(6.2kg/6.35kg)
3
PROPANE CONSTRUCTION HEATER
WARNING
: noT For uSe wiTh duCT work.
sPeciFications
RMC-­‐FA50
DG/DGD/DGP-­‐01
RMC-­‐FA50A
30,000 B TU/hr
50,000 B TU/hr
Propane
Cylinder P ressure
5psig
11" W .C
1.4lbs/hr
2.3lbs/hr
120V, 6 0Hz, 1 Ø
0.65amps
3570rpm
3300rpm
0.16" ( 4mm)
19.3"x8.3"x15.2"
(490x211x386)mm
14.3lbs ( 6.48kg)
RMC-­‐FA60 RMC-­‐FA100
DGD/DGP/DGP-­‐01 DG/DGD/DGP/DGP-­‐
01
RMC-­‐FA100A
30,000 B TU/hr 70,000 B TU/hr
60,000 B TU/hr 100,000 B TU/hr
Propane Propane
Cylinder P ressure Cylinder P ressure
5psig 5psig
11" W .C 11" W .C
1.4lbs/hr 3.3lbs/hr
2.8lbs/hr 4.6lbs/hr
120V, 6 0Hz, 1 Ø 120V, 6 0Hz, 1 Ø
0.65amps 0.7amps
3570rpm 3580rpm
3300rpm 3300rpm
ConMnuous S park ConMnuous S park
0.16" ( 4mm) 0.16" ( 4mm)
25.6"x12.7"x15.6"
19.3"x8.3"x15.2" (650x323x396)mm
(490x211x386)mm 25.6"x11.8"x16.1"
(650x300x409)mm
21.5lbs/21lbs/20.8lbs
14.3lbs ( 6.48kg)
(9.75kg/9.5kg/9.4kg)
CHECK WITH YOUR LOCAL
RMC-­‐FA125
DGD/DGP/DGP-­‐01
70,000 B TU/hr
125,000 B TU/hr
Propane
Cylinder P ressure
5psig
11" W .C
3.3lbs/hr
5.8lbs/hr
120V, 6 0Hz, 1 Ø
0.7amps
3580rpm
3300rpm
ConMnuous S park
0.16" ( 4mm)
25.6"x12.7"x15.6"
(650x323x396)mm
25.6"x11.8"x16.1"
(650x300x409)mm
21.5lbs/21lbs/20.8lbs
(9.75kg/9.5kg/9.4kg)
RMC-­‐FA150
DG/DGD
RMC-­‐FA150A
120,000 B TU/hr
150,000 B TU/hr
Propane
Cylinder P ressure
5psig
11" W .C
5.6lbs/hr
7.0lbs/hr
120V, 6 0Hz, 1 Ø
0.7amps
3580rpm
3300rpm
ConMnuous S park
0.11" ( 2.8mm)
25.6"x11.8"x16.1"
(650x300x409)mm
21.2lbs ( 9.6kg)