350 Three Engine Specifications - Westerbeke 44A FOUR-35 C THREE Operator's Manual

35C
&
350 THREE ENGINE SPECIFICATIONS
Engine Type
Displacement
Aspiration
Combustion Chamber
Bore & Stroke
Rring Order
Direction of Rotation
SPECIFICATIONS
Diesel, four-cycle, three-cylinder, fresh water-
cooled, vertical in-line overhead valve
mechanism ..
80.4 cubic inches (1.318 liter)
Naturally aspirated.
Swirl type.
3.07 x 3.62 inches (78 x 92 mm)
1 - 3 - 2
Clockwise, when viewed from the front.
Compression Ratio 22:1
Dimensions - inches (mm) Height: 21.6 inches
20.1 inches
22.4inches
(540.6 mm)
(510.5 mm)
(596 mm)
Engine Only Width:
Weight
Inclination
Length:
276 Ibs (276 kgs) without transmission.
Continuous 15·
Temporary 25· (not to exceed 30 min.)
TUNE-UP SPECIFICATIONS
Compression Pressure
Minimum
Valve liming
Spilled liming (Static)
Valve Seat Angle
Engine liming
Injector Pressure
Valve Seat Angle
Valve Clearance
(engine cold)
Engine Speed
427 psi (30 kg/cm') at 280 rpm
384 psi (27 kg/cm')
Intake Opens
Intake Closes
17· (spill)
45·
17· BTDC
1991 + 71 - 0 psi (140 + 5 - 0 kgf/cm').
Intake 45·
Exhaust 30·
0.0098 inches (0.25 mm)
3600 rpm (35ClThree)
3000 rpm (35DlThree)
ELECTRICAL SYSTEM
Starting Battery
Battery Capacity
DC Charging Altemator
Starting Aid
Starter
12 Volt, (-) negative ground
400 - 600 Cold Cranking Amps (CCA)
51 Amp rated, belt-driven
Glow plugs, sheathed type
12 Volt, reduction gear
General
Fuel
Fuel Injection Pump
Nozzle
Fuel Riter
Air cleaner
AirFlow
(engine combustion)
Fuel Lift Pump
General
Operating Temperature
Fresh Water Pump
Raw Water Pump
Raw Water Row
(measured before
discharge into exhaust
elbow) Approximate
System Capacity
(Fresh Water)
FUEL SYSTEM
Open flow, self priming.
No.2 diesel oil (cetane rating of 45 or higher).
In-line plunger type (BOSCH).
Throttle type.
Spin-on replaceable
Replaceable paper filter cartridge.
83.7 cfm (2.3 cmm) at 3600 rpm.
69.7 cfm (1.9 cmm) at 3000 rpm.
12 volt DC lift capacity of 5' (1.5 mm) solid state
COOLING SYSTEM
Fresh water-cooled block, thermostatically-
controlled with heat exchanger.
170 -190· F (n -88· C)
Centrifugal type, metal impeller, belt-driven.
Positive displacement, rubber impeller,
belt-driven.
35C/Three 9.5 gpm at 3600 rpm
35D/Three 8.0 gpm at 3000 rpm
5.0 US qts (4.7 liters)
LUBRICATION SYSTEM
General
Oil Riter
Sump Capacity
(not including filter)
Operating Oil Pressure
(engine hot)
Oil Grade
Pressure fed system.
Full flow, paper element, spin-on type.
3.9 U.S. qts (3.7 liters)
50 - 60 psi (3.5 - 4.2 kg/cm')
API Specification CF or CG-4,
Rev. July 2002
Engines & Generators
52