Set Buzzer (Beep/Call Tone); Display Brightness Setting (Led/7-Segment Display); Initialize Settings - Panasonic AK-HRP200G Operating Instructions Manual
Operations and settings remote operation panel
Hide thumbs
Also See for AK-HRP200G:
- Operating instructions manual (44 pages) ,
- Operating instructions manual (41 pages) ,
- Operating instructions manual (20 pages)
Table of Contents
Advertisement
Setup.Mode.Operations.
7-2.Set.pedestal
Press.<UP>.or.<DOWN>.to.select.[PE].and.press.
<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
8..Set.buzzer.(beep/call.tone)
1..
Press.<SELECT>to.select.menu.number.[8].
Select on/off
UP
ND
CC
M.GAIN
DATA
SET
IRIS
DOWN
DISPLAY SELECT
SET UP
ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
Press to exit setup mode
(hold down)
2..
Press.<UP>.or.<DOWN>.to.select.[on].and.press.
<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
9.Display.brightness.setting.(LED/7-segment.display)
Press.<SELECT>to.select.menu.number.[9].
LED display brightness
Adjust brightness
7-segment display brightness
UP
ND
M.GAIN
DATA
SET
DOWN
DISPLAY SELECT
SET UP
ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD
UP+DOWN
LED/7-segment display switch
Press to exit setup mode
(hold down)
(continued)
CC
SHT
SYNC
M.PED
IRIS
CAMERA
SHT
SYNC
M.PED
10-19
No.
SELECT
EXECUTE
Press to confirm
Press to select the
menu number
CC
SHT
SYNC
M.PED
IRIS
CAMERA
CC
SHT
SYNC
M.PED
10-19
No.
IRIS
SELECT
EXIT
EXECUTE
Press to confirm
Press to select the
menu number
9-1.Set.LED.brightness
1..
Press.<SAVE/LOAD>.to.select.[ND].and.press.
<EXECUTE>.to.confirm.the.selection.
• Each press of <SAVE/LOAD> toggles between [ND] (LED display
brightness) and [CC] (7-segment display brightness).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.LED.display.brightness.
and.press.<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
9-2.Set.7-segment.display.brightness
1..
Press.<SAVE/LOAD>.to.select.[CC].and.press.
<EXECUTE>.to.confirm.the.selection.
• Each press of <SAVE/LOAD> toggles between [ND] (LED display
brightness) and [CC] (7-segment display brightness).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.7-segment.display.
brightness.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
Menu.numbers.10.to.15.are.for.future.use.
16.Initialize.settings
<Note>
When settings are initialized, the unit is automatically restarted.For
details on what settings are initialized, refer to page 6
1..
Press.<SELECT>to.select.menu.number.[16].
Select y (Initialize)/n (Cancel)
UP
ND
CC
M.GAIN
DATA
SET
IRIS
DOWN
DISPLAY SELECT
SET UP
ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
Press to confirm
CC
SHT
SYNC
M.PED
IRIS
CC
SHT
SYNC
M.PED
IRIS
CC
SHT
SYNC
M.PED
IRIS
CC
SHT
SYNC
M.PED
IRIS
SHT
SYNC
CAMERA
M.PED
10-19
No.
SELECT
EXECUTE
Press to select the menu number
11
Advertisement
Table of Contents
