Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS
1. Remove all packing materials from the oven cavity, (do not remove the waveguide cover), and the feature sticker
from the outside of the door, if there is one. Check the unit for any damage, such as a misaligned door, damaged door
seals around the door or dents inside the oven cavity or on the door. If there is any damage, please do not operate
the oven until it has been checked by a SERVICE CENTRE APPROVED BY SHARP and repaired, if necessary.
2. Accessories provided
1) Turntable tray
2) Roller stay
3) Low rack
3. Since the door may become hot during cooking, you should place or mount the oven so that the bottom of
the oven is 80 cm or more above floor. You should also keep children away from the door to prevent them
burning themselves.
4. Locate the roller stay in the centre of the oven, then fit the turntable on the roller stay.
Make sure the turntable and roller stay are centrally located and locked together.
NEVER operate the oven without the roller stay and turntable.
5. The oven should not be installed in any area where heat and steam are generated, for example, next to a
conventional oven unit. The oven should be installed so as not to block ventilation openings. When the oven
is mounted on a kitchen benchtop, allow space of at least 40 cm on the top, 5 cm on both sides and at the rear
of the oven for adequate air circulation.
WARNING: The electrical outlet must be readily accessible so that the unit can be unplugged easily in an emergency.
6. Neither the manufacturer nor the distributors can accept any liability for damage to the machine or personal
injury for failure to observe the correct electrical connecting procedure.
The A.C. voltage must be single phase
7. This appliance must be earthed.
8. Operate the oven from a general purpose domestic outlet.
If a generator is used, do not operate the oven with non-sinusoidal outputs.
9. To build the oven into a wall or kitchen cabinet, use an appropriate built-in kit. Sharp built-in kit model number
RK-J90W for R-980J/R-990K(W) and RK-J90S for R-990J(S)/R-990K(S) are available which enable the
microwave oven to be integrated within a kitchen, the kit is available from your retailer. This built-in kit has
been tested according to Australian Standards. Sharp does not recommend the use of any other built-in kit.
If the oven is to be positioned near a conventional oven, ensure that adequate space is allowed, and a suitable
heat shield is incorporated between the two to prevent damage to the oven and the built-in kit caused by heat.
10. Before using CONVECTION HEATER ELEMENTS for the first time, operate the oven without food for 20
minutes at 250°C. This will allow the oil that is used for rust protection to be burned off.
OVEN DIAGRAM
6
4 5
1. Ventilation openings
2. Oven lamp
3. Door hinges
4. Door safety latches
5. See through door
6. Door seals and sealing surfaces
NOTE:
The front-side design is slightly different due to the model you purchased.
Metal racks——High and low
The racks are for Convection, Mix and Grilling. When cooking on Convection or Mix, do not substitute similar
types of racks for these specially designed ones.
High Rack
-This rack is used for two level
cooking in Convection, such as
layer cakes, muffins, biscuits, etc.,
or for Grill cooking.
WARNING:
The accessories will become very hot when in use. Use thick oven gloves when inserting/removing the food or
turntable from the oven to PREVENT BURNS.
4) High rack
5) Cook book
6) Operation manual
• 230V-240V, 50Hz
14
10
12
9
8
11
7
2
4
7. Door open button
8. Touch control panel
9. Digital readout
10. Waveguide cover (Do not remove)
11. Coupling
12. Menu label
1
16
17
1
Low Rack
-This rack is recommended for
roasting and baking in Convec-
tion or Mix mode and can be used
for reheating and cooking foods
by microwave.
5
15
13. Power supply cord
14. Oven cavity
15. Outer cabinet
16. Turntable
17. Roller stay
Hide quick links:
Advertisement
Table of Contents
