Programming The Remote Control - THOMSON ROC4218 User Manual

This universal remote control (4 in 1) is compatible with the majority of television sets, DVD
players and video recorders, as well as digital boxes such as satellite or cable receivers,
DVBT receivers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on.
This remote control was programmed in the factory, so that you can use it to control most
of the sets of the THOMSON group's make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. However, fi rst of all, please activate the remote control by
removing the 2 protective tabs from the 2 CR 2032 batteries.
Please keep this guide along with the code list (provided separately), so that you can subse-
quently programme your remote control for use with other sets.
1:
2 Mode keys: Select the device to control
3 P+, P-:
4 V-, V+:
5 OK:
6:
7 EPG:
8 (Mute):
9 AV:
10:
11:
12:
13:
14 Numeric keys 0 - 9:
15:
16 Setup: Allows you to program your remote before
17 -/--:
18 Menu: Turns on the menu of the selected product.
19 Exit:
20 (rewind): Goes backward (DVD)*.
21 (play):
22 (record):
23:
24 (stop):
25 (pause):
* The coloured buttons can be used to select categories
when teletext is activated, and specifi c functions
depending on the make.
Testing the remote control before
1. Turn on the product you want to control.
2. Press the Mode key that corresponds to the type of
product you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, AUX: any other equipment.
3. Direct the remote control towards your equipment
and try to switch it off by simply pressing the
key G. If the device does not turn off, you must
program the remote control using one of the
methods A, B, C or D described hereafter.
Note 1: Except for the TV key, the DVD, SAT and
AUX mode keys can be programmed to control
a device other than that indicated on the key. It is
therefore possible, for example, to allocate SAT
mode to the DVD key. You must enter the code
corresponding to the manufacturer and the device by
using one of the methods indicated in this manual.
However, method D (automatic search for a code)
will greatly simplify the task for you. In this case it
is only necessary to enter a code from the list that
131793bda.indd Abs1:1 131793bda.indd Abs1:1
The keys
On/Standby or Standby only, depending
on the equipment being used.
(TV, DVD, ...).
Channel Up and Channel Down buttons.
Increases (+) or decreases (-) the volume
of the selected device.
Confi rms a selection.
Allow you to navigate the menus
horizontally and verticaly.
Electronic Program Guide.
Switches the selected appliance sound
on/off.
For selecting an external source (SCART,
HDMI, ...).
Teletext Hold (stop page scrolling).
Displays information of the selected
appliance.
Teletext On.
Teletext Off.
These keys have the same functions as
those of your original remote and are also
used to enter the codes for different
products.
Teletext mix (Teletext inlay on TV picture).
the fi rst use. It also allows you to access to
secondary functions of certain A/V
appliances (Shift). Press and release the
„Setup" key followed by the function key
you want.
In connection with the numeric keys, this
button allows you, with some equipment, to
select directly channels with 2 digits.
Turn off the menu of the selected product.
Play a DVD disc DVD*.
To record, press the RECORD key twice.
Fast forward (DVD)*.
Stop the disc (DVD)*.
Suspends play and stops on an image*.
you programme it
corresponds to the type of device, for example: 0603
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
then test all the codes automatically until it fi nds those
that control the receiver.
Note 2: To control 2 devices of the same type and the
same brand (2 Thomson AUXs, 2 Thomson satellite
receivers, ...) ensure fi rst that these two devices are not
set to react to the same sub code, they will require one
sub code for one and a different sub code for the other
(i.e., codes A and B with Thomson devices). Once you
have checked this, successively program 2 separate
mode keys using method D.
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must fi nd the
subcode of the set to be controlled. Entering a
subcode lets the remote control test a predefi ned list of
codes. Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp fl ashes
to signal that this time is almost up, and then
goes off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, cable, DVBT, ADSL, AUX: any other
appliance.
4. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
5. Direct the remote control towards the set and try to
switch it off by pressing the key G.
6. If the set you want to control switches off, press OK
to memorise the code.
7. Should the set not switch off, press key G repeatedly,
until the set switches off. Between two key presses,
leave enough time for the key corresponding to the
selected mode enough time to light up again (about
1 second). Proceeding this way will enable you to
see whether the set responds or not.
8. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method B – 4-digit codes
programming
Before you start programming, you must fi nd the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp fl ashes
to signal that this time is almost up, and then goes
off).
1
19.08.2008 16:01:25 Uh 19.08.2008 16:01:25 Uh