Page 1 User’s Manual Satellite R20...
Page 2: Table Of Contents
Table of Contents Copyright..........vi Disclaimer .
Page 3 (IEEE1394) ........3-33 TOSHIBA Express Port Replicator ......3-35 Bluetooth USB Adaptor .
Page 4 TOSHIBA support ........
Page 5 Regulatory statements ........G-3 ® Using Bluetooth Card from TOSHIBA equipment in Japan ..G-5 AC Power Cord and Connectors Appendix H Certification agencies .
Page 6: Copyright
This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA Satellite R20 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 7: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394...
Page 8: Eu Declaration Of Conformity
TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PSR20* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE...
Page 9: Japan Regulations
Satellite R20 In the event of problems, you should contact your equipment supplier in the first instance. Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
Page 10 Satellite R20 One of the labels is located on the module. Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■...
Page 11: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 12: Instructions For Ic Cs-03 Certified Equipment
Satellite R20 Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Page 13: Notes For Users In Australia And New Zealand
Satellite R20 Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Page 14 Satellite R20 ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number...
Page 15: General Conditions
Satellite R20 ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
Page 16: Optical Disc Drive Safety Instructions
Satellite R20 Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. TEAC DVD-ROM drive DV-28E ■ The DVD-ROM drive DV-28E employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 17 Satellite R20 Panasonic Communications DVD-ROM & CD-R/RW drive UJDA770 ■ The DVD-ROM & CD-R/RW drive UJDA770 employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Page 18 Satellite R20 TEAC DVD-ROM & CD-R/RW drive DW-224E ■ The DVD-ROM & CD-R/RW drive DW-224E employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Page 19 Satellite R20 Panasonic Communications DVD Super Multi with Double Layer Recording UJ-841 ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 20 Satellite R20 Pioneer DVD Super Multi with Double Layer Recording DVR-K16 ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 21: International Precautions
Satellite R20 International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service...
Page 22 Satellite R20 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S...
Page 23: Preface
This manual tells how to set up and begin using your Satellite R20 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 24 Satellite R20 Icons Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information Keys The keyboard keys are used in the text to describe many computer operations.
Page 25: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 26: Heat Injury
Satellite R20 Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical...
Page 27: Equipment Checklist
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 28 Getting Started Documentation ■ Satellite R20 Portable Personal Computer User's Manual ■ Microsoft Windows XP manual package (Is preinstalled in some regions) ■ Instruction Manual for Safety & Comfort ■ End User License Agreement If any of the items are missing or damaged, contact your dealer immediately.
Page 29 Getting Started Getting Started ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety & Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer.
Page 30: Operating The Computer In Tablet Mode
Getting Started Operating the computer in Tablet mode Change to "The TOSHIBA Satellite R20" computer can be used in two ways, as an ordinary laptop PC and as a Tablet PC. You can use the computer as Tablet PC, operated with the supplied Tablet PC Pen, by turning the LCD display panel through 180 degrees and closing it.
Page 31 Getting Started ■ The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen inside the display area when you use it near the edges of the display panel.
Page 32: Connecting The Ac Adaptor
TOSHIBA Battery Charger (that may have been provided with your PC), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 33 Getting Started 1. Connect the power cord to the AC adaptor. Figure 1-3 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-4 Connecting the power cord to the AC adaptor (3-pin plug) Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled.
Page 34: Opening The Display
Getting Started Opening the display The computer’s LCD display panel can be opened in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly.
Page 35: Starting Up For The First Time
Getting Started 2. Slide and hold the computer’s power button. Power button Figure 1-7 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen.
Page 36: Standby Mode
■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver. ■ To restore operation from Standby Mode, slide the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Page 37: Hibernation Mode
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver located within the Control application (open Performance and Maintenance and then open TOSHIBA Power Saver).
Page 38 For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
Page 39: Restarting The Computer
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the optical disc drive in the Boot Devices menu.
Page 40: Chapter 2 The Grand Tour
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix I. Click the Front with the display closed The following figure the computer’s front with its LCD display panel in the closed position.
Page 41 The Grand Tour System indicators These LEDs let you monitor the status of various computer functions. Refer to the System indicators section for details. Wireless Slide this switch to the left to turn off Wireless communication LAN and Bluetooth functions. Slide it to the right switch to turn on the functions.
Page 42: Left Side
The Grand Tour Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones. Move the Volume control to the right to increase the volume and to the left to decrease the volume. Press the Volume control to Mute the sound. Press the Volume control again to turn Mute off.
Page 43: Right Side
The Grand Tour Keep foreign metal objects, such as screws, staples and paper clips, out of the USB connectors. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly.
Page 44: Back Side
The Grand Tour Tablet PC Pen slot The Tablet PC Pen slot provides storage for the Tablet PC Pen. Tablet PC Pen The Tablet PC Pen is stored within the right side of the computer and enables direct data entry through the display screen.
Page 45 The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...
Page 46: Underside
Battery pack Figure 2-5 The underside of the computer Notches Notches on the computer engage hooks on the TOSHIBA Express Port Replicator to ensure a secure connection. Docking port This port enables connection of an optional TOSHIBA Express Port Replicator and a Slice...
Page 47: Front With The Display Open
The Grand Tour Battery release Slide and hold this latch to release the battery pack for removal. latch For detailed information on removing the battery pack, refer to Chapter 6, Power and Power-Up Modes. Reserve Pen The Reserve Pen is contained in the recess on the underside of the battery pack and enables data entry directly through display screen in addition to the main Tablet PC Pen.
Page 48 The Grand Tour Display hinge The display hinge holds the LCD display panel at easy-to-view angles. Display screen The LCD screen displays high-contrast text and graphics. Refer to Display Controller and Modes section in Appendix B. When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power.
Page 49 Hibernation Mode and shuts down. When you open the computer's LCD display panel the computer starts in Hibernation Mode. Use the TOSHIBA Power Saver to enable or disable this feature. The default is "enabled". Refer to the TOSHIBA Power Saver and Panel...
Page 50: Operation Buttons
The Grand Tour Operation buttons This section describes the operation buttons. Please do not press the buttons too strenuously. CD/DVD button Pressing this button will launch an application program that allows for watching CD/DVD. Pressing this button in the power-on or standby conditions will launch Windows Media Player/WinDVD.
Page 51 The Grand Tour Power The Power indicator glows blue when the computer is on. If you select Stand By from the Turn off computer window, this indicator flashing (one second on, two seconds off) while the computer Standby mode. Battery The Battery indicator shows the condition of the battery’s charge: Blue indicates full charge, orange indicates battery charging and flashing...
Page 52: Keyboard Indicators
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 53: Optical Disc Drives
This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 3, Features, Utilities and Options.
Page 54 The Grand Tour DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drives support the following formats. DVD-ROM drive The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA, CD-Text, Photo CD...
Page 55: Dvd Super Multi Drive Double Layer
The Grand Tour DVD-ROM&CD-R/RW drive The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 56: Ac Adaptor
For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the TOSHIBA AC adaptor that was provided with your PC and the TOSHIBA Battery Charger (that may have been provided with your PC), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the PC.
Page 57: Chapter 3 Features, Utilities And Options
Chapter 3 Features, Utilities and Options Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and...
Page 58 Features, Utilities and Options Legal Footnote (CPU) For more information on the Legal Footnote regarding CPU, please refer to the Legal Footnotes section in Appendix I. Click the *2. Memory Slots 256, 512 or 1,024 MB memory modules can be installed in the two memory slots for a maximum of 2,048 MB system memory.
Page 59 Features, Utilities and Options Disks Hard disk drive Available in five sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) ■ 120.0 billion bytes (111.79 GB) Legal Footnote (Hard Disk Drive (HDD) Capacity) For more information on the Legal Footnote regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix I.
Page 60 Features, Utilities and Options Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 14.1" TFT LCD screen, 16 million colors, with a resolution of 1440 horizontal ×...
Page 61 Features, Utilities and Options Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Page 62: Special Features
Features, Utilities and Options Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Hot keys are specific key combinations that let you quickly change the system configuration directly from the keyboard without running a system program.
Page 63 Refer to Using the Hard Disk Drive (HDD) Protection section in Chapter 4, Operating Basics, for details. The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. User’s Manual...
Page 64: Utilities
To start the utility, to access this utility, click start, click Control Panel, click Printers and Other Hardware and click the TOSHIBA HWSetup icon. TOSHIBA Controls This utility have a section to let you do the following: ■...
Page 65 Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD The TOSHIBA SD memory boot utility allows you Memory Boot Utility to create a bootable SD memory card to start the system. You can access the TOSHIBA SD...
Page 66 Express Port Replicator. To access the utility, select TOSHIBA Mobile Extension from the TOSHIBA Assist application. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
Page 67 "F number" key. The Fn key remains active until another key is pressed. TOSHIBA Direct Disc TOSHIBA Direct Disc Writer is a packet writing Writer software which allows you to write files and/or folders to DVD-RW, CD-RW and DVD+RW discs via a drive letter like a floppy disk or other removable disks.
Page 68: Optional Devices
Secondary portrait The default setting of PC mode is Primary Landscape while that for Tablet mode is Primary Portrait. To start TOSHIBA Rotation Utility, Click start, click All Programs, click TOSHIBA, click Tablet PC and Rotation Utility. Optional devices Optional devices can expand the computer’s capabilities and its versatility.
Page 69: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 70 Features, Utilities and Options 2. Press gently to ensure a firm connection. PC card slot PC card Figure 3-1 Inserting the PC card 3. After inserting the PC card, refer to the PC card’s documentation and check the configuration in Windows to make sure it is appropriate for your PC card.
Page 71: Bridge Media Slot
Features, Utilities and Options Bridge media slot This slot lets you insert SD memory card, SDIO card, Memory Stick (Pro), xD picture card or MultiMediaCard. This Bridge media slot supports the following cards. ■ SD card (SD memory card, SDIO card) ■...
Page 72: Inserting An Sd Card
Features, Utilities and Options SD card Set the SD-card type SD memory cards and Bluetooth ® SDIO cards in the Bridge Media slot. Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
Page 73: Removing An Sd Card
Features, Utilities and Options Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. 4.
Page 74: Formatting An Sd Card
TOSHIBA SD Memory Card Format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD Memory Card Format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Card Format.
Page 75: Removing A Memory Stick
Features, Utilities and Options 2. Press gently to ensure a firm connection. Bridge media slot Memory Stick Figure 3-5 Inserting a Memory Stick Removing a Memory Stick To remove a Memory Stick, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2.
Page 76: Removing An Xd Picture Card
Features, Utilities and Options 2. Press gently to ensure a firm connection. Bridge media slot xD picture card Figure 3-6 Inserting an xD picture card Removing an xD picture card To remove an xD picture card, follow the steps below. 1.
Page 77 Features, Utilities and Options MultiMediaCards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device. You may not use the reproduction of any copyrighted material except for your personal enjoyment.
Page 78: Memory Expansion
When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following...
Page 79: Installing A Memory Module
Features, Utilities and Options If you install a memory module that is not compatible with the computer, the power LED will flashes (on for 0.5 seconds, off for 0.5 seconds) in the following ways; If there is only an error in Slot A: repeatedly flashes orange twice, then blue.
Page 80 Features, Utilities and Options 7. Remove two screws securing the keyboard. Use a point size 1 Phillips screwdriver. 8. Open the latch which holds the keyboard in place, then lift the back of the keyboard toward you, and lay it face down on the palm rest. ■...
Page 81 Features, Utilities and Options The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A. 10. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place.
Page 82: Removing A Memory Module
Features, Utilities and Options Do not bend the keyboard ribbon cable. 13. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard.
Page 83: Battery Pack
Features, Utilities and Options 6. Grasp the sides of the module and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Page 84: Slice Expansion Battery
Features, Utilities and Options Slice Expansion Battery This battery pack increases your computer's operating time when a main battery pack is also installed. For details on using the battery pack, follow the steps below. Connecting the Slice Expansion Battery Follow the steps below to connect the Slice Expansion Battery to the computer.
Page 85: Battery Charger
Features, Utilities and Options 6. Lift off the Slice Expansion Battery (2). Latch Latch Figure 3-17 Removing the Slice Expansion Battery 7. Be sure to replace the protective cap before storing the Slice Expansion Battery. Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer.
Page 86: Connecting Usb Floppy Disk Drive
Features, Utilities and Options Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins. USB connector USB port Figure 3-18 Connecting the USB floppy disk drive...
Page 87: Tablet Pc Pen
Features, Utilities and Options Tablet PC Pen Use it as a spare to your computer. Spare pen tip and draw-out tool are included. Refer to Chapter 4, Operating Basics, for the detailed usage. Reserve Pen Supplied pen uses a pen instead of Supplied pen at the time of loss or breakage.
Page 88: Changing The Resolution
Features, Utilities and Options You can connect a television set to the S-Video out port on the computer. Follow the steps below. 1. Turn the computer off. 2. Use the TV adaptor cable's S-Video plug (not supplied) to connect the television to the S-Video out port.
Page 89: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 90 Features, Utilities and Options Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Figure 3-21 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...
Page 91: Toshiba Express Port Replicator
Features, Utilities and Options TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source.
Page 92: Bluetooth Usb Adaptor
Bluetooth wireless standard. Security lock Security locks enable you to anchor your computer and optional TOSHIBA Express Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or TOSHIBA Express Port Replicator.
Page 93: Options
AC adaptor for each site so you will not have to carry the adaptor with you. Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. Slice Expansion This battery pack increases your computer's...
Page 94 Features, Utilities and Options Bluetooth USB When connected to one of the computer's USB Adaptor ports, the Bluetooth USB adaptor allows wireless communications to be carried out with Bluetooth- compatible equipment. Wireless Optical The Bluetooth Wireless Mouse is an optical Mouse with mouse that is compatible with the Bluetooth Bluetooth...
Page 95: Chapter 4 Operating Basics
Chapter 4 Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Page 96: Using The Tablet Pc Pen And Reserve Pen
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.
Page 97 The lead cannot be replaced if it is worn (use the Reserve Pen only). TOSHIBA is not liable for any problems arising on the products due to the use of the Tablet PC Pen in an environment where the above conditions are not satisfied or because of its use by unspecified number of users.
Page 98: Pen Actions
Operating Basics Removing the Tablet PC Pen Remove the Tablet PC Pen as described below. 1. Gently push the Tablet PC Pen towards the middle of the computer. The pen will then protrude slightly from the side. Tablet PC Pen Tablet PC Pen slot Tablet PC Pen slot Tablet PC Pen slot...
Page 99: Single Tap
A short and worn pen point is difficult to pull out. Replace the pen point with a refill before it becomes too short to remove. ■ It is recommended that you keep another pen set as a spare. You can buy replacement pen sets from your TOSHIBA authorized dealer. User’s Manual...
Page 100: Removing The Reserve Pen
LCD display panel. When the pen tip breaks replace it with one of the refills delivered with the Tablet PC Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer. Removing the Reserve Pen To remove the Reserve Pen case, follow the steps below.
Page 101: Changing To The Tablet Mode
Operating Basics 3. Reinstall the battery pack. Refer to the Replacing the battery pack section in Chapter 6, Power and Power-Up Modes for more information on how to remove and reinstall the battery pack. Changing to the Tablet mode To change from laptop mode to the Tablet mode, follow the instructions below.
Page 102 Operating Basics 1. Open the LCD display panel to the upright position. Check that the angle of the keyboard and the LCD display panel is 90 degrees. 2. Rotate the LCD display panel clockwise slowly. ■ When rotating LCD screen of your computer, be sure to slowly turn the screen in the proper direction, and not apply excessive force or speed.
Page 103: Changing The Screen Orientation
Operating Basics 6. Press the LCD display panel downward softly. Display latch Slit Figure 4-11 Changing to the Tablet mode (4) Changing the screen orientation The orientation of the computer screen can be changed to one of the following four display modes: Secondary portrait Primary portrait Primary landscape...
Page 104: Accelerometer Utilities And Toshiba Rotation Utility
1. Press the Cross Function Button for more than one second. The TOSHIBA Tablet Menu will appear. 2. Select the Internal Monitor icon in Toshiba Shortcut using the Cross Function Button and then press then Cross Function Button. 3. Select the rotation angle using Cross Function Button and then press the Cross Function Button.
Page 105: Using Accelerometer Utilities
■ This may cause injury to children or adults, or damage to the computer. When the TOSHIBA HDD protection function is turned on and the Tilt function (function to start applications, etc. by waving the computer vertically or horizontally) is used, the TOSHIBA HDD protection message may be displayed on the screen.
Page 106: Changing To The Laptop Mode
Operating Basics It is safer if you hold the computer with both hands horizontally as shown in the below example. The computer is shaken horizontally. The computer is shaken perpendicularly. Figure 4-13 Shake the computer Changing to the laptop mode To change the operating mode to the Laptop Mode, follow the instructions below.
Page 107: How To Swipe The Finger
Operating Basics How to Swipe the Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you when in portrait mode, and sideways when in either landscape mode or Laptop mode.
Page 108 Operating Basics Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects.
Page 109: Points To Note About The Fingerprint Utility
Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 110 Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the "User Enrollment" Wizard. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration.
Page 111: Window Logon Via Fingerprint Authentication
■ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
Page 112 Password and Windows Logon Password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.
Page 113: Using Optical Disc Drives
TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 114 Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Figure 4-15 Pressing the eject button and pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-16 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend...
Page 115: Removing Discs
Operating Basics 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the disc tray to close it. Press gently until it locks into place.
Page 116 Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the CD/DVD. Figure 4-18 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place.
Page 117: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs.
Page 118: When Writing Or Rewriting
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW media is affected by the quality of the disc and the way it is used.
Page 119: Writing Cd/Dvds On Dvd Super Multi Drive
You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM discs. The following applications for writing are provided: TOSHIBA Disc Creator, and TOSHIBA Direct Disc Writer, and InterVideo’s WinDVD Creator Platinum. ■...
Page 120: Before Writing Or Rewriting
Operating Basics Before writing or rewriting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-R DL/+R/+R DL/- RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 121 Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Hitachi Maxell Ltd. ■ This drive cannot use discs that allow writing faster than 8 speed (DVD- R, DVD+R), 4 speed (DVD-RW, DVD+RW), 5 speed (DVD-RAM), 2.4 speed (DVD+R DL, Double Layer supported model only), 2 speed (DVD-R DL, Dual Layer supported model only).
Page 122 LAN server or any other network device. ■ Writing with software other than TOSHIBA Disc Creator and InterVideo WinDVD Creator Platinum are not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD- R/RW, DVD-R/-R DL/-RW/-RAM or DVD+R/+R DL/+RW disc.
Page 123: Toshiba Disc Creator
TOSHIBA Disc Creator cannot record in packet format. ■ You might not be able to use the “Disc Backup” function of TOSHIBA Disc Creator to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that was made with other software on a different DVD-R/-R DL/- RW or DVD+R/+R DL/+RW recorder.
Page 124: Data Verification
3. Select File Open or Full Compare mode. 4. Click the OK button. TOSHIBA Direct Disc Writer Note the following limitations when you use TOSHIBA Direct Disc Writer: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R/+R DL, DVD-R/-R DL, and CD-R discs that are not rewritable.
Page 125: Important Information For Use
Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound appears choppy - in this instance please follow the instructions below: 1.
Page 126 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Page 127: Media Care
Operating Basics ■ WinDVD Creator cannot export to DVD-Audio, VideoCD or miniDVD format. ■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the disc may only play on your computer. ■ When writing to a DVD disc, WinDVD Creator requires 2GB or more of disk space for every one hour of video.
Page 128: Sound System
Operating Basics Floppy disks 1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.
Page 129: Modem
Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 130: Properties Menu
Operating Basics 2. The Region Selection icon will appear in the Windows Task Bar. 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.
Page 131 Operating Basics Connecting To connect the modular cable, follow the steps below. The modular cable that comes with the computer must be used to connect the modem. Connect the end of the modular cable with the core to the computer. ■...
Page 132: Wireless Communications
Operating Basics If you use a storage device such as an optical drive or hard disk drive connected to a 16-bit PC card, you might experience the following modem problems: ■ Modem speed is slow or communication is interrupted. ■ Skips may occur in sound.
Page 133: Bluetooth Wireless Technology
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology ®...
Page 134 ® ® This Bluetooth Stack is based on the Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use ® Bluetooth other than TOSHIBA mobile computers. ® ®...
Page 135: Wireless Communication Switch
Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■...
Page 136: Lan
Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T) is supported with some models.
Page 137: Connecting Lan Cable
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 138: Cleaning The Computer
■ Before moving the computer, it is recommended that you change the function of the TOSHIBA HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter.
Page 139: Using The Hard Disk Drive (Hdd) Protection
This function does not guarantee that the hard disk drive will not be damaged. ■ The secondary hard disk drive is not supported by the TOSHIBA HDD protection function. When vibration is detected, the following message is displayed, and the icon in the notification area of the taskbar is changed to the protection state.
Page 140: Taskbar Icon
You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection Setting. The window can also be started from the icon on the Taskbar or from the Control Panel.
Page 141 AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode. Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-24 Details Detection Level Amplification...
Page 142: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
Page 143: Chapter 5 The Keyboard
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 144: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 145: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 146 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
Page 147 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 148: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an "F number" key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 149: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 150: Numeric Mode
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay:...
Page 151: Generating Ascii Characters
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 152: Chapter 6 Power And Power-Up Modes
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
Page 153 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) 2nd battery fully • Operates • No charge adaptor charged • No charge • LED: 2nd battery blue connected • LED: 2nd battery blue DC IN blue DC IN blue 2nd battery •...
Page 154 When the main battery is not charging. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a Slice Expansion battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 155: Power Indicators
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, 2nd battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the 2nd battery indicator to determine the status of the Slice Expansion battery.
Page 156: Battery Types
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual.
Page 157 The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 158: Care And Use Of The Battery Pack
Keep the battery pack out of reach of infants and children. It can cause injury. ■ Use only battery packs recommended by TOSHIBA as replacements. ■ Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened.
Page 159: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 160: Battery Charging Notice
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 161: Maximizing Battery Operating Time
■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: ■...
Page 162: Replacing The Battery Pack
Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below.
Page 163 Power and Power-Up Modes ■ Do not remove the battery pack while the computer is in Standby Mode. Data is stored in RAM, so if the computer loses power it will be lost. ■ In Hibernation Mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed.
Page 164: Toshiba Password Utility
TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in the TOSHIBA Password Utility are different from the Windows password. User Password To start the utility, point to or click the following items: start ->...
Page 165 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 166: Supervisor Password
Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.
Page 167: Tablet Mode
PC Pen. An * (asterisk) is displayed after "Password =" and one character is input for every tapping. Register your password to the computer in the laptop mode using the standard keyboard. Refer to TOSHIBA Password Utility, in this chapter for the detail. User’s Manual...
Page 168: Power-Up Modes
Chapter 1, Getting Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.
Page 169: Chapter 7 Hw Setup & Bios Setup
Chapter 7 HW Setup & BIOS Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 170 HW Setup & BIOS Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or an external monitor.
Page 171: Boot Priority
HW Setup & BIOS Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM*...
Page 172 HW Setup & BIOS Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
Page 173 HW Setup & BIOS Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as Built-in HDD ->...
Page 174 HW Setup & BIOS Setup This function lets you set the CPU operating mode. ® This option is displayed only for models with an Intel Core ® processor and Intel Core Solo processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled.
Page 175 HW Setup & BIOS Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). USB KB/Mouse Legacy Emulation Use this option to enable or disable USB keyboard/mouse legacy emulation.
Page 176: Bios Setup Program
■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the...
Page 177: Virtualization Technology
HW Setup & BIOS Setup Ending the BIOS Setup Program Halfway The configuration settings can be terminated halfway without saving any of the changes made. 1. Press the Esc key. The "Exit without saving? (Y/N)" message is displayed. 2. Press the Y key. The BIOS setup program will end.
Page 178: Diagnostic Mode
Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
Page 179: Chapter 8 Troubleshooting
Chapter 8 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 180: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 181: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 182: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 183: Ac Power
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing blue AC power If you have trouble turning on the computer with the AC adaptor connected,...
Page 184 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver. Consider using a power saving mode. User’s Manual...
Page 185: Real Time Clock
Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
Page 186: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup & BIOS Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 187 Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.
Page 188 Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.
Page 189: Dvd Super Multi Drive
Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 190: Usb Floppy Disk Drive
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAM Check the region code on the DVD.
Page 191: Xd Picture Card
Troubleshooting SD card Refer also to Chapter 3, Features, Utilities and Options. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an Make sure the card is not write protected. SD memory card You cannot read a file Make sure the target file is on the SD memory...
Page 192: Pointing Device
Troubleshooting MultiMediaCard Refer also to Chapter 3, Features, Utilities and Options. Problem Procedure MultiMediaCard error Reseat the MultiMediaCard to make sure it is occurs firmly connected. Check the MultiMediaCard’s documentation. You cannot write to an Make sure the MultiMediaCard is not write MultiMediaCard protected.
Page 193: Usb Mouse
Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab. 3.
Page 194: Fingerprint Sensor
Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse control utility. moves too fast or too slow 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab. 3.
Page 195: Usb Device
Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the USB ports on the computer and the USB device. work Make sure the USB device drivers are properly installed.
Page 196 Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Page 197: Tv Output Signal
Troubleshooting TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, Keyboard.
Page 198 Troubleshooting Problem Procedure You place a call, but a Make sure the settings are correct in your connection can’t be communications application. made After making a call you Make sure the tone or pulse selection in your can’t hear a ring communications application is set correctly.
Page 199: Disposing Of Pc And Pc Batteries
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist, contact your LAN administrator.
Page 200: Toshiba Support
All data deletion costs will be borne by you. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 201 Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia Germany & Austria TOSHIBA Australia Pty. Ltd.
Page 202 TOSHIBA Information Systems Systems, Inc. (U.K.) Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany User’s Manual 8-24...
Page 203: Appendix A Specifications
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 348 (w) × 260 (d) × 39.9 (h) millimeters (not including parts that extend beyond the main body) Refer to User’s Manual about Weight. Environmental Requirements Conditions Ambient temperature Relative humidity Operating...
Page 204 Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands...
Page 205 Specifications Network control unit (NCU) Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
Page 206: Display Controller And Modes
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Because of the LCD’s increased resolution, lines may appear broken in DOS mode. The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen.
Page 207 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 208 AT Commands Answer command This command instructs the modem to go off-hook and answer an incoming call. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
Page 209 AT Commands Disables echo to the computer. Enables echo to the computer (default). Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default).
Page 210 AT Commands Result Codes: n=0,1,2,3 ERROR Otherwise Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
Page 211 AT Commands Result Codes: n=0,1 ERROR Otherwise Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric...
Page 212 AT Commands Dial tone detect Disabled:The modem dials a call regardless of whether it detects a dial tone. Enabled:The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 213 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
Page 214 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
Page 215 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
Page 216: Appendix D S-Registers
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 217 S-registers Range:0-255 Default:0 Units:rings Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range:0-225 Default:0 Units:rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 218 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 219 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range:0-255 Default:2 Units:seconds...
Page 220 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 221: At Command Set Result Codes
S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
Page 222 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
Page 223: V.90 Mode
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 224 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 225: At Command
V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 226: Wireless Lan
Appendix F Wireless LAN Card Specifications Form Factor PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. ■...
Page 227: Radio Characteristics
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Page 228: Supported Frequency Sub-Bands
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 229 Wireless LAN ■ For Wireless LAN cards installed in wireless clients that operating in a peer-to-peer mode, the card will use the default channel 10. ■ In a Wireless LAN Access Point, the Wireless LAN card will use the factory-set default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device.
Page 230 Wireless LAN 5745 5765 5785 5805 5825 User’s Manual...
Page 231: Appendix G Bluetooth Wireless Technology Interoperability
Bluetooth wireless technology Interoperability ® Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
Page 232 ® Always use Bluetooth Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe http://www.pc.support.global.toshiba.com in the United States for more...
Page 233: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 234 ■ Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused ® by unauthorized modification of the devices included with this Bluetooth Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 235: Using Bluetooth ® Card From Toshiba Equipment In Japan
FCC radio frequency exposure limits. Nevertheless, the ® Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used in this device are located at the upper edge of the LCD screen, and this device has been tested as portable device as defined in Section 2.1093 of FCC rules when the LCD screen is rotated 180 degree...
Page 236 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 237: Device Authorization
Bluetooth wireless technology Interoperability Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law. The Name of the radio equipment: EYXF3CS JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D05-0074001...
Page 238: Ac Power Cord And Connectors
Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
Page 239 AC Power Cord and Connectors Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 240: Appendix I Legal Footnotes
Appendix I Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual.
Page 241: Memory (Main System)*3
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 242: Hard Disk Drive (Hdd) Capacity*5
Legal Footnotes Hard Disk Drive (HDD) Capacity 1 Gigabyte (GB) means 10 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 2 = 1,073,741,824 bytes, and therefore shows less storage capacity.
Page 243: Glossary
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 244 Glossary IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock...
Page 245 Glossary ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
Page 246 Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Page 247 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 248 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 249 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 250 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 251 Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps.
Page 252 Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions.
Page 253 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 254 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 255 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 256: Index
6-11 using 4-19 BIOS Setup 7-8 writing 4-25 Bluetooth 3-5, 4-39 DVD-ROM drive Bluetooth Stack for Windows by problems 8-9 Toshiba 3-9 using 4-19 problems 8-21 DVD-ROM&CD-R/RW drive Wireless Optical Mouse with Bluetooth problems 8-10 Technology 3-36 using 4-19...
Page 257 Satellite R20 location 2-8 wireless setting 5-5 problems 8-16 HW Setup 3-8 using 4-12 accessing 7-1 Floppy disk care 4-34 Boot priority 7-3 Fn + Ctrl (enhanced keyboard simulation) CPU 7-6 device config 7-7 Fn + Enter 5-3 display 7-2...
Page 258 Satellite R20 problems 8-20 Touch Pad location 2-8 using 4-1 Power Media care 3-15, 4-33 button location 2-8 Card care 3-15 conditions 6-1 CD/DVDs 4-33 hibernation mode 1-11 floppy disks 4-34 indicators 6-4 Memory card care 3-15 panel on/off 3-7, 6-17...
Page 259 Satellite R20 USB floppy disk drive 8-12 TOSHIBA Power Saver 3-8 USB mouse 8-15 TOSHIBA SD Memory Boot Utility 3-9 Wireless LAN 8-21 TOSHIBA Virtual Sound 3-10 xD picture card 8-13 TOSHIBA Zooming Utility 3-9 Processor 3-1 TV 3-32 Restarting the computer 1-13...

Toshiba Satellite R20 User Manual

User's Manual

Chapter 1 Getting Started

Chapter 2 The Grand Tour

Chapter 3 Features, Utilities and Options

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup & BIOS Setup

Chapter 8 Troubleshooting

Appendix A Specifications

Appendix B Display Controller and Modes

Appendix Cat Commands

Appendix D S-Registers

Appendix E V.90

Appendix F Wireless LAN

Appendix G Bluetooth Wireless Technology Interoperability

Appendix H AC Power Cord and Connectors

Appendix I Legal Footnotes

Pointing Device

Quick Links

Chapters

Related Manuals for Toshiba Satellite R20

Summary of Contents for Toshiba Satellite R20