Advertisement
Quick Links
Advertisement
Related Manuals for Smeg CMVANILLA
Summary of Contents for Smeg CMVANILLA
- Page 1 Instructions Manual CMVANILLA – CMVERTIGO - CMZOOM...
-
Page 2: Table Of Contents
INDEX RECOMMENDATIONS AND SUGGESTIONS ........................3 CHARACTERISTICS ................................4 INSTALLATION..................................8 USE ...................................... 19 MAINTENANCE ................................... 21... -
Page 3: Recommendations And Suggestions
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. -
Page 4: Characteristics
CHARACTERISTICS Components (Chic-Vanilla models) Ref. Q.ty Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support Plate (with lamp holder). Power supply cable lock Cable raceway Glass Glass fixing plates Pawl Ref. Q.ty Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.5 Screws M4 x 20... - Page 5 Components (Vertigo model) Ref. Q.ty Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support Plate (with lamp holder) Power supply cable lock Cable raceway Glass or Panels the other material Pawl Ref. Q.ty Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.5 Chrome plated glass fixing Pin/Screw...
- Page 6 Components (Zoom model) Ref. Q.ty Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support plate. Power supply cable lock Cable raceway Pawl Ref. Q.ty Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.5 Screws for pawl Q.ty Documentation Instruction Manual...
- Page 7 Dimensions...
-
Page 8: Installation
INSTALLATION This hood is designed to be mounted on the ceiling/on a shelf, above a free-standing Hob (min. 650 mm), in: • Ducting version: Evacuation to the outside. • Recirculation version: Internal recirculation. Warning: The F-Light hood is a system comprising hood + lamp, so that two separate electrical wiring systems must be provided, one for the hood and one for the lamp. - Page 9 Ceiling/Shelf drilling and Plate Fixing CEILING/SHELF DRILLING • Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling/Shelf. • Rest the plate against the ceiling/shelf, taking care to keep the limit pawl that has just been fitted in a position facing the installer and the cooking hob (the limit pawl must not be con- fused with the other 4 used to fix the steel cables that move the Hood).
- Page 10 FIXING THE PLATE • Lift up the fixing plate, taking care to ensure that the limit pawl is positioned frontally. • Fit the slots onto the two screws previously inserted in the ceiling, and turn until they are at the centre of the adjustment slot.
- Page 11 CONNECTING HOOD-PLATE CABLES N.B. Before continuing with installation it is necessary to move the hood to a height of at least 650 mm from the cooker hob, using a support or the assistance of an- other person. This is essential, as the hood cables must necessarily be connected to the plate fitted to the ceiling without the weight of the hood bearing on the structure.
- Page 12 • Attention to the direction of the plate fixed to the ceiling (the limit pawl on the plate fastened to the ceiling has a corresponding hole on the plate cover and on the hood canopy). • Insert the cables into the safety knobs (c) with the thread at the top.
- Page 13 • Pass the cables through the slots in the threaded pawls (a) and screw the cable locking screws (b) to the pawls them- selves. • When the operation has been completed the result must be as shown in the figure for all 4 ca- bles.
- Page 14 • At this point it is possible to connect up the hood, and the lamp if there is one, to the power supply using the respective power cables. • Close the plate cover using the 3 screws removed previously and the wrench provided •...
- Page 15 Connections AIR OUTLET - DUCTING VERSION To install the hood in the ducting version, please refer to the instructions provided in the ducting kit specific to the hood. AIR OUTLET – RECIRCULATION VERSION • Open the lighting unit by pulling on the notch provided. •...
- Page 16 LEVELLING THE HOOD • The hood mobile unit must be levelled to allow the movement to operate properly. • The hood is levelled by adjusting the safety pawls. • Rest a spirit level on the hood. • When the safety knobs are pressed upwards, movement of the hood is “unlocked”.
- Page 17 FIXING THE POWER SUPPLY CABLE • Wind the power cable around its axis so that it forms a spiral from the mobile body to the plate in the ceiling. • It is important to do this to prevent the wire come out from the hood body during the closing of the hood •...
- Page 18 FITTING THE GLASS – CHIC-VANILLA MODELS • Take the lamps and insert them in the lamp holders. • They do not have to be screwed in, but simply inserted all the way. • Fix the glass 5 to the plate using the screws 12d and washers 22 in the top part.
-
Page 19: Use
Control panel Button Function Display Turns the lights On/Off. Hood Down On/Off Press for 2 seconds to raise the Hood. Press briefly to turn the Motor On/Off. Hood Up Off/Off Press once: The Hood lowers. Press a second time: The Hood Stops. When the movement has been completed the motor turns on at Speed two. -
Page 20: Remote Control
REMOTE CONTROL The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included). • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. -
Page 21: Maintenance
MAINTENANCE Grease filter The filter must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. CLEANING METAL SELF- SUPPORTING GREASE FILTER • Open the lighting unit by pulling on the nocth. •... - Page 22 Lighting LIGHT REPLACEMENT 20 W halogen light. • Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. • Remove the halogen lamp from the lamp holder by pulling gently. • Replace the lamp with a new one of the same type, making sure that you insert the two pins properly into the housings on the lamp holder.
- Page 23 Additional information for the installation technician • Open the lighting unit by pulling on the notch provided. • Apply the label, indicated the type of lighting, on the Hood as indicated in the figure (Rif.A). Procedure to be used in case of malfunction on the movement •...
- Page 24 991.0266.243_ver1...