HP ProLiant BL680c Specification page 20

QuickSpecs
Core Options
HP Processors
HP Memory
HP Hard Drives
NOTE: The BL680c G7 supports two, three, or four processors. One processor is not
supported.
NOTE: The minimum processor configuration is two processors that must be installed
in sockets CPU1 and CPU3.
NOTE: All processors within the server must be identical.
NOTE: All -B21 processor kits listed below contain one (1) processor.
NOTE: If upgrading an existing BL680c G7 server to a different processor, the server's
ROM must be flashed to the latest BIOS prior to the upgrade.
NOTE: Intel® Xeon® E7-4800/8867L series processors cannot be used to upgrade a
ProLiant BL680c G7 server blade with Intel® Xeon® 6500/7500 series processors.
Ten-Core Processors
HP BL680c G7 Intel® Xeon® E7-4870 (2.40GHz/10-core/30MB/130W) Processor Kit
HP BL680c G7 Intel® Xeon® E7-4860 (2.26GHz/10-core/24MB/130W) Processor Kit
HP BL680c G7 Intel® Xeon® E7-4850 (2.00GHz/10-core/24MB/130W) Processor Kit
HP BL680c G7 Intel® Xeon® E7-8867L (2.13GHz/10-core/30MB/105W) Processor Kit
Eight-Core Processors
HP BL680c G7 Intel® Xeon® E7-4830 (2.13GHz/8-core/24MB/105W) Processor Kit
HP BL680c G7 Intel® Xeon® E7-4820 (2.0GHz/8-core/18MB/105W) Processor Kit
Six-Core Processors
HP BL680c G7 Intel® Xeon® E7-4807 (1.86GHz/6-core/18MB/95W) Processor Kit
NOTE: All DDR3 memory option kits consist of one RDIMM per kit.
NOTE: See the "Memory" section for memory guidelines, installation rules, and
additional general information.
HP 4GB (1x4GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9 Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9 Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9 Low Power
Memory Kit
HP 16GB (1x16GB) Dual Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9 LP
Memory Kit
HP 16GB (1x16GB) Quad Rank x4 PC3-8500 (DDR3-1066) Registered CAS-7 Memory Kit
HP 32GB (1x32GB) Quad Rank x4 PC3L-8500 (DDR3-1066) Registered CAS-7 LP Memory
Kit
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller,
firmware, and the server backplane) should operate at the same data transfer rate or
the system bandwidth will be negotiated down to an acceptable level for all
components.
NOTE: Hard drives have either a one year or three year warranty; refer to the specific
hard drive QuickSpecs for details.
NOTE: A minimum of two drives are required for RAID 0 and 1, three dries for RAID 5,
and four drives for RAID 1+0 and 6.
NOTE: SAS, SATA, and/or SSD drives cannot be mixed within the server.
SAS Hot Plug SFF (2.5-inch) Enterprise (ENT) Drives
DA - 13742 North America — Version 35 — December 13, 2013
HP ProLiant BL680c Generation 7 (G7) Server Blade
643766-B21
643768-B21
643770-B21
643778-B21
643772-B21
643774-B21
643776-B21
500658-B21
500662-B21
604506-B21
627812-B21
500666-B21
627814-B21
Page 20