Digital Audio Inputs; Headphone Jack; Auxiliary Ir Input - Bryston B100 Owner's Manual

labeled AUX1/PHONO accept moving magnet phono cartridge inputs. These inputs are NOT line level AUX1/PHONO AUX1/PHONO accept moving magnet phono cartridge inputs. These inputs are NOT line level
inputs in the B100-P and cannot be used as such.
LINE LEVEL ANALOG AUDIO OUTPUTS : The Bryston B100 integrated amplifier comes equipped
with 2 pairs of gold plated analog RCA jacks for outputs: PREAMP OUT and
• PREAMP OUT is normally connected, internally, via the PREAMP OUT is normally connected, internally, via the PREAMP OUT
AMP IN
• RECORD OUT output is not affected by volume, balance or mute controls. RECORD OUT RECORD OUT output is not affected by volume, balance or mute controls.

DIGITAL AUDIO INPUTS:

there are 4 digital audio inputs available.
Two TOSLINK optical inputs are selected by pressing the TV (TOSLINK-1) or
the front panel (when in digital mode) or, on the handheld remote, by pressing DIGITAL-TV or
buttons.
Two SPDIF coaxial inputs can be connected to the B100-DA using the RCA input jacks labeled AUX-2/SPDIF-
1 and AUX-2/SPDIF-2. To select these inputs first place the unit in digital mode by pressing the ANALOG/
DIGITAL button on the front panel (or the A/D button on the handheld remote) and then press the CD or
button on the front panel (DIGITAL-CD or
font panel ANALOG/DIGITAL switch in ON concurrently with either the CD, TV,
digital mode is engaged. When the LED is OFF the B100-DA is in analog mode and the two SPDIF input jacks
now function as analog line level audio inputs (AUX-
See the DIGITAL-to-ANALOG CONVERTER OPTION section for more information. DIGITAL-to-ANALOG CONVERTER OPTION section for more information. DIGITAL-to-ANALOG CONVERTER OPTION

HEADPHONE JACK:

Bryston B-100 integrated amplifier. The headphone output is driven directly from the preamplifier section uti-
lizing separate headphone buffers. Inserting the headphone jack mutes the loudspeakers automatically (indi-
cated by the mute LED on the front panel turning red). The B100 PREAMP OUT is also muted.
You can adjust the volume setting of the headphones by using the volume control on the front of the B-100
integrated amplifier. You may also utilize the remote control unit to adjust headphone volume. The headphones
cannot be muted with the remote control unit or the front panel Mute. Only headphones with impedances of
greater than 50 ohms should be used.

AUXILIARY IR INPUT:

remote control system provides an output from their infra-red LED drive circuit. The signal connected to this jack
should be ≥1.8Vdc and ≤ 9Vdc. The tip of the phone jack is positive (+) and the ring is negative (-).
LED STATUS IN LED STATUS LED STATUS IN DICATORS:
CLIPPING:
MUTE:
POWER:
ANALOG/DIGITAL:
AUX1, CD, TUNER, TV/SAT VIDEO & RECORD:
In the B100-DA model, which contains a stereo D/A converter module,
DIGITAL-CD DIGITAL-CD or DIGITAL-TUNER on the remote). When the green LED above the DIGITAL-TUNER on the remote). When the green LED above the DIGITAL-TUNER
There is a quarter inch headphone output jack available on the front panel of the
This mono 1/8" (3mm) phone jack allows a direct connection to equipment whose
This LED (light emitting diode) will flash RED when the output waveform is clipped thus
indicating an overload condition.
Lights GREEN to indicate the outputs are muted..
GREEN indicates normal operation
RED indicates Standby
Blinking RED/GREEN a fault or thermal overload problem in the unit.
In B100-DA models: when this LED is illuminated green concurrently with either
CD, TUNER, TV or VIDEO LEDs, it indicates that the digital inputs SPDIF-
SPDIF-2, TOSLINK-1 or TOSLINK-2 (respectively) have been selected.
In B100 & B100-P models: when illuminated green this LED indicates that the line level
analog audio input AUX-2 has been selected. AUX-2 AUX-2 has been selected.
indicate the active input. In digital mode these LEDs will light RED if the bit stream is
PREAMP OUT and PREAMP OUT
CONNECTED/SEPARATE CONNECTED/SEPARATE switch, to CONNECTED/SEPARATE switch, to
TV TV (TOSLINK-1) or
AUX 2). AUX-
PREAMP OUT PREAMP OUT is also muted.
TOSLINK-2 TOSLINK-2 (respectively) have been selected.
One of these input source LEDs will light green to
2
B100
TWO TWO CHANNEL POWER AMPLIFIER TWO CHANNEL POWER AMPLIFIER
RECORD OUT RECORD OUT. RECORD OUT.
VIDEO VIDEO (TOSLINK-2) buttons on VIDEO (TOSLINK-2) buttons on
DIGITAL-TV DIGITAL-TV or
TV TUNER or VIDEO LEDs, then TV,
ring ring is negative (-).
POWER
DIGITAL-VIDEO
CD CD or TUNER
SPDIF 1, SPDIF-