Moving-Magnet Phono Stage Option; Wired Rs232 Remote Control - Bryston B100 Owner's Manual

WIRED RS232 REMOTE CONTROL:

Using the DB9-female connector at the rear of the unit, the B100 can receive commands via a null modem cable at
9600 baud, 8 data bits, no parity and 1 stop bit (9600,8,N,1). Valid commands will return the ">" character indicating
that the unit is ready to receive a new command. An invalid command will return the "!" character. These serial data
commands are as follows:
000 - power off
001 - select analog source 1 (A/D)
002 - select analog source 2 (AUX/PH)
003 - select analog source 3 (CD)
004 - select analog source 4 (TUNER)
005 - select analog source 5 (TV)
006 - select analog source 6 (VIDEO)
007 - volume up
008 - volume down
DIGITAL-to-ANALOG (D/A) CONVERTER OPTION: DIGITAL-to-ANALOG (D/A) CONVERTER OPTION:
The B100-DA comes equipped with stereo Digital-to-Analog converter (D/A or DAC) module. This module is
also retrofittable to standard B100 units.
A unique feature of the B100-DA is its ability to utilize up to four independent digital sources (two SPDIF and
two TOSLINK). These four digital inputs can be accessed by selecting CD,
with the DAC feature enabled (by pressing the Analog/Digital button on the left side of the front panel).
Activate the DAC feature by pressing the ANALOG/DIGITAL button on the left side of the front panel (or A/D
on the remote). The LED over the ANALOG/DIGITAL button will turn Green. Pressing any of the following
four buttons will cause their LEDs to light green, as well, to indicate a PCM digital source is present and con-
nected properly.
SPDIF 1 is accessed by selecting CD on the front panel or DIGITAL-CD on the remote.
•
SPDIF 2 is accessed by selecting TUNER on the front panel or DIGITAL-TUNER on the remote.
•
Optical 1 is accessed by selecting TV on the front panel or
•
Optical 2 is accessed by selecting VIDEO on the front panel or
•
The source LED's will turn GREEN when a PCM digital bit stream is present. If there is no bit stream available
or an incorrect bit stream (NON-PCM) the LED will turn RED.
You may re-select Analog by simply depressing the ANALOG/DIGITAL button once more and the LED will
extinguish.
All of the above functions are available from the hand held remote control as well .

MOVING-MAGNET PHONO STAGE OPTION:

The B100-P contains a moving magnet phono stage. The Phono Stage is modular and can be added to the stan-
dard B100 model later if required by your Bryston dealer.
Bryston's MM Phono section features state-of-the-art accuracy in equalization, extremely low noise and distor-
tion, and provides headroom margins sufficient to prevent overload from any known phono source. To access the
Phono section simply plug your left/right turntable interconnect leads into the left/right AUX-1/PHONO inputs on
the rear panel of the B100 and press the AUX-1/PHONO button on the front panel. The AUX-1/PHONO LED will
turn green. If your turntable provides a separate ground lead, system noise may be minimized by connecting it to
the ground lug in the center of the rear panel.
015 - power on/off toggle
019 - balance left
020 - balance right
029 - power on
058 - mute on
059 - mute off
061 - record monitor toggle 248 - Clear Trigger 2 for current source
062 - record monitor on
063 - record monitor off
TV TV on the front panel or
VIDEO VIDEO on the front panel or
4
B100 B100 B100
TWO CHANNEL POWER AMPLIFIER TWO CHANNEL POWER AMPLIFIER
081 - select digital source 1 (CD)
082 - select digital source 2 (TUNER)
083 - select digital source 3 (TV)
084 - select digital source 4 (VIDEO)
245 - set/reset Pass Through mode
247 - Set Trigger 2 for current source Trigger 2 Trigger 2 for current source
Trigger 2 Trigger 2 for current source
255 - System reset; restore defaults
CD TUNER, CD, TUNER, TUNER TV and VIDEO sources
DIGITAL-CD DIGITAL-CD on the remote.
DIGITAL-TUNER on the remote. DIGITAL-TUNER
DIGITAL-TV on the remote. DIGITAL-TV on the remote. DIGITAL-TV
DIGITAL-VIDEO on the remote. DIGITAL-VIDEO on the remote. DIGITAL-VIDEO
AUX-1/PHONO AUX-1/PHONO inputs on
AUX-1/PHONO AUX-1/PHONO LED will