Ronda 5040.F User Manual

Cal. 5040.F
English
User's Manual

Description of the display and control buttons

Display elements
Minute hand
Second hand
Month
Day of week
Hour hand
Date
Centre stop-second
Minute counter
1 ⁄ second counter
10
(hour counter after 30 minutes)
Minute counter Second coutner
�
�
�
��� ���
Push-button A
1 ⁄ second counter
10
��� ���
�
Push-button B
Minute counter Centre
stop-sencond
�
��� ���
� ��
1 ⁄ second counter
10
Push-button B
��� ���
�
� ��
Push-button B
Second hand
�
��� ���
� ��
��� ���
�
� ��
�
��� ���
� ��
Day of week
��� ��� �
� ��
��� ���
Control buttons
Corrector D (day)
Corrector E (month)
��� ���
Push button A
Crown
Push button B
Corrector C (date)
Chronograph:
Accumulated timing
�
Example:
Start: (start timing)
�
� Stop: (e.g. 15 min 5 sec following
Restart: (timing is resumed)
�
* Stop: (e.g. 13 min 5 sec following
�
= 28 min 10 sec
(The accumulated measured time is shown)
Reset:
�
The 3 chronograph hands are returned to
their zero positions.
Please note:
* Following , the accumulation of the
�
timing can be continued by pressing
push-button A
(Restart / Stop, Restart / Stop, ...)
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not
in their correct zero positions and have to be
adjusted (e.g. following a battery change).
Pull out the crown to position II
�
(all 3 chronograph hands are in their
correct or incorrect zero position).
Keep push-buttons A and B depressed
�
simultaneously for at least 2 seconds
(the centre stop-second rotates by
360° � corrective mode is activated).
�

Setting the time

�
* Pull out the crown to position II
�
(the watch stops).
� Turn the crown until you reach the correct
time 8.45.
* Push the crown back into position I.
�
Please note:
* In order to set the time to the exact second,
must be pulled out when the second
�
hand is in position «60» (I).
Once the hour and minute hands have been
set, must be pushed back into position I
�
at the exact second.
Setting the time, date,
day of week and month
�
Example:
– On the watch: 10 /
MON / JAN / 1:25 AM
– Current: 20 /
THU / OCT / 8:30 PM
* Pull out the crown to position II
�
(the watch stops).
** Turn crown until the current time
�
is shown.
* Push crown to position I
�
(watch continues to run).
�
Please note
* To set your watch to the exact second
please refer to the chapter entitled
«Setting the time»
** Please observe the AM/PM clock rhythm
RONDA AG
CH-4415 Lausen/Switzerland
www.ronda-startech.com
Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW)
Accuracy: +20 / -10 seconds per month
In case your watch needs to be repaired or to raise claims
under a guarantee, please contact the point of sales
Second coutner
Minute counter
��� ���
⁄ second counter
1
10
��� ���
Push-button B
Minute counter Second coutner
��� ���
� )
)
�
1 ⁄ second counter
10
��� ���
Push-button B
A
B
A
B
A
�
� ��
Date
��� ���
�
Corrector C
��� ���
Corrector D Corrector E
�
��� ���
�
Corrector C
Day of week Month
��� ���
Date
Chronograph: Basic function
(Start / Stop / Reset)
�
�
Example:
Push-button A
Start: Press push-button A.
�
Stop:
� to stop the timing, press
push-button A once more and read
the 3 chronograph counters:
4 min / 5 sek / 7 ⁄ sec
10
Zero positioning:
�
Press push-button B.
(The 3 chronograph hands will be reset to
their zero positions).
�
Chronograph:
Intermediate or interval timing
�
� Example:
Push-button A
Start: (start timing)
�
Display interval:
�
e.g. 10 minutes 10 seconds (timing
�
continues in the background)
�
* Making up the measured time:
�
(the 3 chronograph hands are quickly
Push-button B
advanced to the ongoing measured time).
Stop: (Final time is displayed)
�
Reset:
�
The 3 chronograph displays are returned
to their zero position
Please note:
* Following , further intervals or inter-
�
mediates can be displayed by pressing
�
push-button B (display interval / make up
measured time, ...)
�
Adjusting the centre stop second
A
Single step 1 x short
A
long
Continuous
�
Adjusting the next hand B
�
Adjusting the 1 ⁄ second counter hand (position 6h)
10
A
Single step 1 x short
A
Continuous long
�
Adjusting the next hand B
�
Adjusting the minute counter (position 9h)
A
Single step 1 x short
A
Continuous long
�
� Returning the crown to position I
Termination of the chronograph hands
adjustment (can be carried out at any time).

Setting the date (quick mode)

Example after a change of month:
– Date on watch: 31
�
– Current date: 1
Press the corrector C once to adjust the
�
date 1 day forward.
Please note
�
The date for the following day must be set
during the date changing phase between
9:00 PM and 00:20 AM.
�
�
Press the corrector C to gradually
�
advance the date hand.
Press the corrector D to gradually
�
�
advance the day of week.
Press the corrector E to gradually
�
advance the month.
�