Supermicro X10SLM-F_X10SLL Quick Reference Manual

S
UPERMICR
R
X10sLm-f_X10sLL(-f/sf/s)
Q r g
uICk eferenCe uIde
Motherboard Layout and Features
SW1
VGA
LED1
BMC FW
BMC
CTRL
BIOS
X10SLM-F/X10SLL(-F/SF/S)
Rev. 1.02
PCH
T-SGPIO1
T-SGPIO2
I-SATA3 I-SATA0 JSD1
JBT1
FP Control
JF1
FANA FAN3
I-SATA4 I-SATA1
I-SATA5 I-SATA2
CPU Installation Heatsink Installation
Load Plate
Thermal Paste
Load Lever
Push Down
Pin 1
North Center Edge Turn Clockwise
to Lock
CPU Properly Turn Counter-
Installed clockwise to
Unlock
Connect the Heatsink Wire to
Load Lever Locked
the CPU Fan Connector
into Place
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
C I
ontaCt nformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
USB6/7
COM1
COM2
USB4/5
LAN2 LAN1
IPMI_LAN
JPL2
JP8 JPL1
CPU
IPMI Code
BAR Code
MAC Code
SP1
JSTBY1
JP7
JP1
JPME1
JBR1
JL1
J7 JD1 JRK1 JPME2 FAN2 FAN2 FAN1
JP2
= mounting hole
Front Panel Control (JF1)
20 19
Ground
NMI
X X
FP PWRLED 3.3 V
HDD LED UID Switch
NIC1 Activity LED 3/3V Stby
3/3V Stby
NIC2 Activity LED
OH/Fan Fail Blue LED Cathode
Power Fail LED
3.3V
Reset Reset Button
Ground
Power Button
Ground PWR
2 1
guide.
Jumpers, Connectors and LED Indicators
Jumpers
Jumper Description
JI C1/JI C2 SMB to PCI Slots On (Enabled)
2 2
JPB1 (-F Models only) BMC Enable Pins 1-2 (Enabled)
JBR1 BIOS Recovery Pins 1-2 (Normal)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPME1 ME Recovery Pins 1-2 (Normal)
JPME2 Manufacturing Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Enable Pins 1-2 (Reset)
Connectors
Connector Description
BT1 Onboard Battery
COM1/COM2 COM1/COM2 Port Headers
Fan1-Fan4, FanA System/CPU Fan Headers
JD1 Speaker/Power LED Indicator
JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JIPMB1 4-pin External BMC I 2 C Header (for an IPMI Card)
JPI 2 C1 Power System Management Bus (Power SMB)
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 4-pin CPU power Connector (Required)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSTBY1 Wake-On-LAN Enable Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
(IPMI_)LAN (for -F Models) IPMI_Dedicated Gigabit (RJ45) Port
SP1 Internal Speaker/Buzzer
I-SATA0-I-SATA5 (Intel PCH) Serial ATA (SATA 3.0/2.0) Ports 0-5 (Ref. Model Table on P.
1-4)
(CPU) Slot 6 PCI-Express 3.0 x8 in x16 Slot
(CPU) Slot 5 PCI-Express 3.0 x8 Slot
(PCH) Slot 4 PCI-Express 2.0 x4 in x8 Slot (X10SLM-F/x10SLL-F Only),
T-SGPIO 1/2 Serial_Link General Purpose I/O Connection Headers 1/2
USB 3.0-0 (USB0) Front Accessible Vertical USB 3.0 Type A Header
USB 3.0-2/3 (USB2/3) Front Accessible USB 3.0 Header 2/3 (for X10SLM-F Only)
USB 4/5, 6/7 (2.0) Backpanel USB 2.0 Ports 4/5, 6/7 (USB 6/7: for X10SLM-F &
X10SLL-F Only)
USB 8/9 Front Panel Accessible USB 2.0 Headers 8/9
VGA Backpanel VGA Port
LED Indicators
LED Description Color/State
LED1 BMC Heartbeat LED Green: Blinking
LED4 System Standby Power LED Orange: Solid on
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
P C
aCkage ontents
• One (1) Supermicro Motherboard
• Two (2) SATA Cables
• One (1) I/O Shield
Memory Support
The X10SLM-F_X10SLL-(F/SF/S) supports up to 32GB of Unbuffered ECC
(UDIMM) DDR3 1600/1333 MHz in 4 memory slots.
Default
Note: The X10SLL-S/-SF supports up to 16 GB of DDR3 memory in 2
DIMM modules.
DIMM Memory Installation
Memory Population Guidelines
Please follow the table below when populating the X10SLM-F_X10SLL-(F/SF/S).
DDR3 Unbuffered ECC (UDIMM) Memory
DIMM Slots per DIMMs Populat- DIMM Type
Channel ed per Channel
2 1 Unbuffered
DDR3
2 2 Unbuffered
DDR3
Populating these DIMM modules with a pair of memory modules of the same
type and same size will result in interleaved memory, which will improve memory
performance.
Note: Insert the desired number of DIMMs into the memory slots, start-
ing with the blue slots first, i.e., DIMMB2, DIMMA2, then DIMMB1 and
DIMMA1. See the illustration below for DIMM slot locations. For the system
to work properly, please use the memory modules of the same type and
speed in the same motherboard.
Towards the CPU
Slot 1, Channel A
Slot 2, Channel A
(Blue Slot)
Slot 1, Channel B
Slot 2, Channel B
(Blue Slot)
Towards the edge of the motherboard
Press Both Notches
Straight Down into the
Memory Slot
Back Panel I/O Connectors
D
F
Status
BMC Normal
C E G H
A
Power On
B
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
POR Speeds Ranks per DIMM (any
combination)
1333, 1600 Single Rank, Dual Rank
1333, 1600 Single Rank, Dual Rank
Notches
Release Tabs
Backplane I/O Panel
A. COM1 F. USB Port 5 (2.0)
B. USB Port 6 (2.0) G. LAN1
C. USB Port 7 (2.0) H. LAN2
I
D. IPMI LAN I. VGA
E. USB Port 4 (2.0)