Supermicro X10SLA-F Quick Reference Manual

S
UPERMICR
R
X10sla-f
Q r g
uICk eferenCe uIde
Motherboard Layout and Features
LE5
BMC
JI2C2
JI2C1
J19
J18
JPG1
JPME1
JPME2
PCH
BIOS
LICENSE
BAR CODE
MAC CODE Battery
JBT1
IPMI CODE
I-SATA0
I-SATA3
I-SATA1
SPKR1
I-SATA2
I-SATA5
BIOS
JSD1
Tools Needed:
Screwdriver
CPU Installation Heatsink Installation
Load Plate
Thermal Paste
Load Lever
Push Down
Pin 1
North Center Edge
Turn Clockwise
to Lock
CPU Properly
Turn Counter-
Installed
clockwise to
Unlock
Connect the Heatsink Wire to
Load Lever Locked
the CPU Fan Connector
into Place
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
C I
ontaCt nformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
USB2/3
USB4/5
SW1
VGA COM1
LAN2 LAN1
IPMI _LAN
X10SLA(-F)
Rev. 1.01
CPU
LE3
= mounting hole
Phillips Screws (9) Standoffs (9)
Front Panel Control (JF1)
20 19
Ground
NMI
X X
FP PWRLED 3.3 V
ID_UID_SW/3/3V Stby
HDD LED
NIC1 Link LED NIC1 Activity LED
NIC2 Activity LED
NIC2 Link LED
Blue+ (OH/Fan Fail/
Red+ (Blue LED Cathode)
PWR FaiL/UID LED)
Power Fail LED 3.3V
Reset
Ground Reset Button
Power Button
Ground PWR
2 1
guide.
Jumpers, Connectors and LED Indicators
Jumpers
Jumper Description
JBT1 CMOS Clear
JI C1/JI C2 Disable SMB to PCI Slots
2 2
JPG1 VGA Enable
JPL1/JPL2 LAN1/LAN2 Enable
JPME1 ME Recovery
JPME2 Manufacture Mode Select
JPUSB1 USB Wake Up Enable
JWD1 Watch Dog Enable
Connectors
Connector Description
Battery Onboard Battery
COM1/COM2 COM1/COM2 Port Headers
Fan1 - Fan4, FanA System/CPU Fan Headers (Fan1: CPU Fan)
JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JLED1 Power LED Indicator Header
JP1 2 C1 Power SMB (System Management Bus)
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 8-pin CPU power Connector (Required)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN IPMI_Dedicated LAN
SPKR1 Internal Speaker/Buzzer
I-SATA0/I-SATA1 (Intel PCH) Serial ATA (SATA 3.0) Ports 0/1 (6Gb/sec)
I-SATA 2 - I-SATA5 (Intel PCH) Serial ATA (SATA 2.0) Ports 2~5 (3Gb/sec)
(PCH) Slot 7 PCI-Express 2.0 x4 in x8 Slot
(CPU) Slot 6 PCI-Express 3.0 x16 Slot
Slot 1 - Slot 5 PCI 33MH Slots (5V)
SW1 UID (Unit Identifier) Switch
T-SGPIO 1/2 Serial_Link General Purpose I/O Connection Headers 1/2
USB 2, 3, 4, 5 Backpanel USB 2.0 Ports 2, 3, 4, 5
USB 0 (3.0), USB 1 (3.0) Front Accessible USB 3.0 Ports 1, 2
USB 8/9 Front Panel Accessible USB 2.0 Headers 8/9
VGA Backpanel VGA Port
LED Indicators
LED Description Color/State
LE3 Onboard Standby Power LED Green: Solid on
LE4 UID LED Blue: On
LE5 (X10SLA-F Only) BMC Heartbeat LED Green: Blinking
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
P C (a t a I P
aCkage ontents PPlIes o n dIvIdual
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
Memory Support
The X10SLA(-F) supports up to 32GB of Unbuffered (UDIMM) DDR3 ECC/Non-
Default
ECC 1600/1333 MHz in 4 memory slots.
(See Chpt. 2)
Pins 2-3 (Disabled)
DIMM Memory Installation
Pins 1-2 (Enabled)
Memory Population Guidelines
Pins 1-2 (Enabled)
Pins 1-2 (Normal) Please follow the table below when populating the X10SLA(-F).
Pins 1-2 (Normal))
DDR3 Unbuffered ECC/Non-ECC (UDIMM) Memory
Pins 1-2 (Enabled)
DIMM Slots per DIMMs Populat- DIMM Type
Channel ed per Channel
Pins 1-2 (Reset)
2 1 Unbuffered
2 2 Unbuffered
Insert the desired number of DIMMs into the memory slots, starting with DIMMA1
(Channel A, Slot 1). For the system to work properly, please use the memory
modules of the same type and speed in the same motherboard.
Channel A Slot 1
Channel A Slot 2
(Blue Slot)
Channel B Slot 1
Channel B Slot 2
(Blue Slot)
Press both notches
straight down into
the memory slot.
Back Panel I/O Connectors
D
Status
F
Power On
Unit Identified
BMC Normal
A C E G H
B
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
o )
aCk nly
POR Speeds Ranks per DIMM (any
combination)
1333, 1600 Single Rank, Dual Rank
DDR3
1333, 1600 Single Rank, Dual Rank
DDR3
Towards the CPU
Notches
Release Tabs
Backplane I/O Panel
A. COM1 F. USB Port 4 (2.0)
B. USB Port 3 (2.0) G. LAN1
C. USB Port 2 (2.0) H. LAN2
D. IPMI_LAN I. VGA
E. USB Port 5 (2.0) J. UID Switch
J
I