Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1. Press the TOOLS button. Press the ENTER E button to select Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select
On or Off.
If your receiver supports audio only, it may not appear in the device list.
N
The receiver will work when you have properly connected the Optical IN jack of the
N
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the
N
TV's Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1
channel sound to the Home theater receiver. When the source is a digital component
such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
If there is a power interruption to the TV when the
N
the Speaker Select may be set to External Speaker when you turn the TV on again. (see page 22)
Troubleshooting for Anynet +
Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet+ device...
appears on the screen.
The Anynet + device does not
play.
The connected device is not
displayed.
The TV programme cannot be
recorded.
The TV sound is not output
through the receiver.
BN68-02355EG-Eng.indb 31
Receiver is set to On (by disconnecting the power cord or a power failure),
Solution
•
Check if the device is an Anynet
•
Connect only one receiver (home theater).
+ device power cord is properly connected.
•
Check if the Anynet
+ device's Video/Audio/HDMI 1.3 cable connections.
•
Check the Anynet
Anynet+ (HDMI-CEC) is set to On in the Anynet + setup menu.
•
Check whether
•
Check whether the TV remote control is in TV mode.
+ exclusive remote control.
•
Check whether it is Anynet
+ doesn't work in certain situations. (Searching channels, Operating Plug & Play, etc.)
•
Anynet
•
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again
or turn your TV off and on again.
+ Function of Anynet + device is set on.
•
Check if the Anynet
•
Check if the Anynet+ device is properly connected to the TV and check if the
(HDMI-CEC) is set to On in the Anynet + Setup menu.
•
Press the
TV button on the TV remote control to switch to TV. Then press the TOOLS button
to show the Anynet+ menu and select a menu you want.
+ menu.
•
Select View TV in the Anynet
•
Press the
SOURCE button on the TV remote control and select a device other than Anynet+
devices.
•
(Note that the channel button operates only when a tuner-embedded Anynet
connected.)
•
You cannot use the remote control when you are configuring Anynet
mode.
•
Use the remote control when the Anynet
•
You cannot use the play function when
•
Check whether or not the device supports Anynet
•
Check whether or not the HDMI 1.3 cable is properly connected.
Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
•
Check whether
+ devices again.
•
Search Anynet
+ device using the HDMI 1.3 cable only. Some HDMI cables may
•
You can connect an Anynet
not support Anynet + functions.
•
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power
cord or a power failure, please repeat the device scan.
•
Check whether the antenna jack on the recording device is properly connected.
•
Connect the optical cable between TV and the receiver.
English - 31
View TV
Device List
Record
DVDR MENU
DVDR INFO
Receiver
Setup
+ device. The Anynet + system supports Anynet + devices only.
+ setting or switching to view mode is complete.
Plug & Play is in progress.
+ functions.
:
DVDR
◄
On
►
Move
Adjust
Return
U
L
R
Anynet +
+ device is not
+ or switching to a view
2009-06-30
10:31:47