I
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1
Press the TOOLS button.
Press the A or
'f
button to select Receiver, then press the ENTER button.
2
Press the
<IIlI
or
~
button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3
Press the EXIT button to exit.
~
When the receiver (home theater) is set to On, you can hear sound output from
the TV's Optical jack. When the TV is displaying a OTV(air) signal, the TV will
send out 5.1 channel sound to the Home theater receiver. When the source is a
digital component such as a OVO and is connected to the TV via HOMI, only 2
channel sound will be heard from the Home Theater receiver.
~
If your receiver supports audio only, it may not appear in the device list.
~
The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of
the TV.
~
When using the WISELINK feature, sound may not output properly through the receiver.
~
When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred
language) menus.
~
If there is a power interruption to the TV when the Receiver is On (by disconnecting the power cord or a power
failure), the TV Speaker may be set to "Off' when you turn the TV on again.
Troubleshooting for Anynet+
I
Symptom
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The message Connecting to
Anynet+ device... appears on the
screen.
The Anynet+ device does not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
The TV sound is not output through
the receiver.
Solution
•
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
only.
•
Connect only one receiver (home theater).
•
Check if the Anynet+ device power cord is properly connected.
•
Check the Anynet+ device's Video/Audio/HOM I 1.3 cable connections.
•
Check whether Anynet+ (HOMI-CEC) is set to On in the Anynet+ setup menu.
•
Check whether the TV remote control is in TV mode.
•
Check whether it is Anynet+ exclusive remote control.
•
Anynet+ doesn't work in certain situations. (Searching channels, Operating WISELlNK)
•
When connecting or removing the HOMI 1.3 cable, please make sure to search devices
again or your TV off and on again.
•
Check if the Anynet+ Function of Anynet+ device is set on.
•
Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HOMI-CEC) is set to On in the Anynet+ Setup menu.
•
Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet+ menu and select a menu you want.
•
Select View TV in the Anynet+ menu.
•
Press the SOURCE button on the TV remote control and select a device other than
Anynet+ menu.
•
Press CH, CH LIST, PRE·CH, and FAV.CH to change the TV mode.
(Note that the channel button operates only when an Anynet+ device with a built-in tuner is
not connected.)
•
You cannot use the remote control when you are configuring Anynet+ or switching to a
view mode.
•
Use the remote control when the Anynet+ setting or switching to view mode is complete.
You cannot use the play function when Plug
&
Play is in progress.
•
Check whether or not the device supports Anynet+ functions.
•
Check whether or not the HOMI 1.3 cable is properly connected.
•
Check whether Anynet+ (HOMI-CEC) is set to On in the Anynet+ setup menu.
•
Search Anynet+ devices again.
•
You can connect an Anynet+ device using the HOMI 1.3 cable only. Some HOMI cables
may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English ·104