Tally T6218 Maintenance Manual Supplement page 27

8
7
PROPRIETARY NOTICE
This document and the information contained therein are the
property of TALLY. Recipient agrees not to:
(1) use such information for purposes other than those expressly
authorized by TALLY; and (2) furnish such information
to any other person in whole or in part without the prior express
written permission of TALLY; and, to promptly return
this document to TALLY upon the receipt of a request
therefor.
14
25
2X
2X
D 7
12
15
24
C
2X
28
TO CBA POWER
DISTRIBUTION
17
4X
B
SHOCK MOUNTS GO
INTO 2 OUTERMOST
& 2 INNERMOST
HOLES ON BOTTOM
OF CHASSIS.
083931, 083932, 083935, 083936,
083937, 084369, 084370, 084371 &
A
8 7
16-0001E-21
6
10
2X
7
11
VIEW C
27
084372 ASSY
6
5 4
TO "PAPER OUT
TO "PAPER MOTION
SENSOR"
SENSOR"
(LOWER TRACTOR"
(UPPER TRACTOR)
VIEW C
20
9
16
7 7 BOTH END
7
18
13
19
27
2X
084372 613335 T6218 -
V
084371 -
613335 T6218 V
-
084370 613335 V
T6218
084369 613335 T6218 -
V
UNLESS OTHERWISE SPECIFIED
083937 613335 -
T6215 V
DIMENSIONS AND TOLERANCES ARE
IN INCHES AND SHALL BE INTER-
083936
613335 T6215 V -
PRETED PER ANSI Y14.5M-1982.
083935 613335 V -
T6215
0.X ±0.1
083932 613335 V - 0.XX ±0.01
T6215K
0.XXX ±0.005
083931 613335 T6215 V -
0.XXXX ±0.0005
PART NUMBER NEXT ASSY MODEL REV SHT ANGLE ±0°30'
APPLICATION
5 4
3 2
SYM DATE
- 11/30/99 RELEASE TO PRODUCTION
A 12/16/99 REVISED PER DCR #28937
B 1/14/00 REVISED PER DCR #28990
3/10/00 REVISED PER DCR'S C, D & E #29090
E
H 5/31/00 REVISED PER DCR'S F, G & H #29296
J 7/6/00 REVISED PER DCR #29416
K 7/13/00 REVISED PER DCR #29450
L 7/18/00 REVISED PER DCR #29451
P 11/22/00 REVISED PER DCR'S M, N & P #29636
S 3/27/01 REVISED PER DCR'S R & S #29899
U 5/10/01 REVISED PER DCR'S T & U #30034
TO "CBA POWER
8/10/01 REVISED PER DCR #30146
DISTRIBUTION" V
21
UPPER TRACTOR DRIVE BELT TO BE TENSIONED SUCH THAT
WHILE THE PHASING LEVER IS IN EXTREME DOWN POSITION,
A 1 POUND FORCE APPLIED TO THE LONGEST SPAN 2.7 in.
FROM THE CENTER OF THE PAPER MOTOR PULLY RESULTS IN
A MAXIMUM BELT DEFLECTION BETWEEN 0.163 in-0.203in.
22 LOWER TRCTOR DRIVE BELT TO BE TENSIONED SUCH THAT A
1 POUND FORCE APPLIED TO THE LONGEST SPAN 2.7 in.
FROM THE CENTER OF THE PAPER MOTOR PULLY RESULTS IN
A MAXIMUM BELT DEFLECTION BETWEEN 0.203in-0.253in.
23 ALTERNATE ASSY FOR ITEM 55 IS: 611507-083133.
22
3X
21 3X
23 3X
26 A/R
ITEM
PART NUMBER
DESCRIPTION
NO.
QTY REQ
DWN YUEN LAI
9/2/99
CHKD 11/30/99
T. HUI
PRE-REL M. O'LEARY
11/30/99
TOLERANCES ARE:
FINAL M. O'LEARY
11/30/99
MFG M.V. McGURR 12/1/99
Q.A. TIM SCHORN
12/1/99
THIRD ANGLE
C.S. C. MARTIN 12/1/99
PROJECTION
CHG BD D. STARR 12/1/99
DO NOT SCALE DRAWING
3 2
1
REVISIONS
DESCRIPTION BY APPROVED
YL TH MBO
YL TH MBO
YL TH CB
YL TH CB
YL TH CB
YL TH CB
YL TH DD
YL
TH MBO
D
YL
TH DB
YL TH CB
YL TH JPC
YL
NOTES: (UNLESS OTHERWISE SPECIFIED)
1. MANUFACTURE, ASSEMBLE & PART MARK PER TALLY
WORKMANSHIP STANDARDS.
2. REMOVE ALL BURRS, BREAK SHARP EDGES, MACHINE
SURFACES 125 -.
3. ALL DIMENSIONS APPLY AFTER SURFACE COATINGS
HAVE BEEN APPLIED.
4. NUMBER WITHIN CIRCLE INDICATES ITEM OR FIND
NUMBER, SEE PARTS LIST FOR SPECIFICATION.
5. UNLESS OTHERWISE NOTED BY , LENGTHS OF
STANDARD FASTENERS MAY BE ADJUSTED TO CONFORM
C
TO TALLY WORKMANSHIP STANDARDS.
6. ALL SURFACES TO COMPLY WITH TALLY SPECIFICATION
D1094, CLASS C.
7 APPLY A LIGHT COAT OF GREASE ITEM 67, BETWEEN ITEM
54 AND SIDE PLATE, AROUND STANDOFF. OR INDICATED
AREA.
INSTALL ITEMS 51, 52 & 61 WITH ZERO CLEARANCE TO
8
ITEM 60, AND LOCK IN PLACE WITH ITEM 74.
9 CLEAR O.D. OF BEARING TO REMOVE OIL PRIOR TO ASSY
WITH SPEED BONDER (ITEM 68).
END OF SHAFT (ITEM 59) TO BE 0.01 TO 0.05 BELOW FLUSH
10
WITH OUTSIDE SURFACE OF END PLATE.
11 WIPE INSIDE OF BEARING BORE WITH ACTIVATOR ITEM 69
LESS THAN 1 HOUR PRIOR TO ASSEMBLY.
12 SLIDE ITEM 64 MOTOR DOWNWARD FOR PROPER TENSION
IN TOP BELT, THEN SLIDE ITEM 53 IDLER ASSY DOWN AND
TIGHTEN FOR PROPER TENSION IN THE LOWER BELT.
SET PROPER TRACTOR PHASING WITH ITEM 54 PHASING LEVER
IN MID-TRAVEL & PLATEN FULLY CLOSED WHILE USING THE
TRACTOR PHASING GAGE.
13 TORQUE TO BE SET AT 18 IN-LBS.
14 POSITION ITEM 58 TO FIRMLY CONTACT ITEM 62, ITEM 58 TO
BE NO MORE THAN 0.125 BELOW OUTSIDE END OF ITEM 51
OR ITEM 52.
B
15 ADJUST SHAFT (ITEM 58) TO BEAR TO SPRING (ITEM 62) WITH
5 LBS ±2.5 LBS OF LOAD.
16 TORQUE TO BE SET AT 14~15 IN-LBS.
17 TORQUE TO BE SET AT 18~20 IN-LBS.
18 UPPER AND LOWER SHAFTS (ITEM 95) MUST BOTH BE FULLY
ENGAGED WITH KNOB (ITEM 96) AND PULLEY (ITEM 100)
PRIOR TO INSTALLATION OF BELT (ITEM 93) TO ENSURE
PROPER UPPER AND LOWER SHAFTS PHASING.
19 TEAR AWAY THIS PORTION OF FOAM (ITEM 30) ALONG
PERFORATION FOR 083935, 083937, 084370 & 084372 ASSY ONLY.
20 ADJUST IDLER SUPPORT (ITEM 94) TO ACHIEVE BELT
TENSION OF _______ _______.
LIMITED USE, SEE P/L.
MATERIAL FINISH
A
MAILING: P.O. BOX 97018
KENT, WA 98064-9718 USA
SHIPPING: 8301 So 180TH ST.,
KENT, WA 98032 USA
TITLE
PRINT MECHANISM ASSY
SIZE CODE IDENT DWG NO. REV
613333
D
V
12344
SCALE: NONE FILE NAME: 3333V SHEET 1 OF 6
1