Clearances
Design Information
36"
Refrigerators,
Freezers
130°D00rswing
[ %'1°
130°
',.y
1
90° Door Swing /
!'
i36-3/4"
4"_Min.
to Wall
Factory
set for a 150 ° door swing. Order WX14X99
adjustable
door stop to reduce swing to as little as 90 ° .
When Installed
into a corner:
Allow 25" for a full 130 ° door swing. Allow 15" for pan
removal.
Allow 4" rain. clearance
when door swing is
adjusted
to a 90 ° opening
for pan access, but pan
removal
is restricted.
%%
Wa
--25"--
Min. to
Wall
0 _
_q
130° Door
m
130° Door
Swing
m
Swing
II
q-'
'-F
i
/
/
Z
4
I',
z:ff x
"::::-:::,,,,
::::::::z
"X
///
",',,
,( ,"
',3-"
Clearances for Multiple Single Door Installations
In a side-by-side installation of a left and right door
swing product, no clearance between the units is
required. If you are installing 3/4" thick custom
panels, order ZUG75 Unified Grille Panel Kit for
one continuous grille panel.
2 _
\,, ',,,[
'_,',
', \
.....
*,, ,,,
Clearances
for two products
installed
side-by-side
with the same (left or right} door swing
Allow 2" minimum
clearance
between
the products
to
prevent door swing interference.
Order the WX14X99
adjustable
door stop to reduce the factory
set 130 °
door swing. Allow 15" minimum
to a wall to achieve
full drawer
extension
and pan removal. Additional
clearances
are required when using custom
handles
and panels.
NOTE: ZUG75 Grille Panel Kit will not fit this
installation.
5"
!
3'
/
ft
'
",
....
X/
x-....
...... .,
Clearances
for two
products
installed
side-bg-side
with right
and left side hinges
together
Allow 5" minimum
between
the two products
to
prevent
one door from striking
the othel: Use the
WX14X99
adjustable
door stop to reduce the factory
set 150 ° door swing and to allow pan removal.
Additional
clearances
are required when using
custom
handles
and panels.
NOTE: ZUG75 Grille Panel Kit will not fit this
installation.
Side By Side
Installation
Of Freezer
And Refrigerator
For a complete
food storage
center,
install a Honogram
Freezer and
Refrigerator
side by side. Order ZUG75
Unified Grille Panel Kit for one
continuous
5/4" panel.
, Electrical
and water
locations
must
be located
as shown
for either type
of installation.
A separate
115V,
60Hz. 20 amp power suppl U is
recommended
for each product.
NOTE: Additional cutout width may be
required when side panels are used. Add
side panel thickness to the finished cutout to
calculate rough-in width. See installation
examples below.
f
_FinishedWidth
1_2-1/2"
i
I_
_Electrical%
_28-1/2
'_
84-1/2" max I _- 24-3/4" Total
!
83-1/2"rain I I
Depth
Finished II
,
_
,
i
Opening I I I-1/2"vvate_,bupP'Y3-1/2";
_2
3-I/2"
10'_
Freezer
Refrigerater
*72" rain. for a flush installation
7:[-:[/2" rain. for a semi-flush installation
WallView
75"From Floor
to Bottom
of Electrical
Area
Installation
Examples
Side panels are required whenever
the sides of the
product
will be exposed.
1/2" to 5/4" side panels are normally
set into place
and fastened
to adjacent
cabinetry
or back wall
before rolling the refrigerator
or freezer into the
opening.
Therefore, the rough-in dimensions must allow
for side panel thickness. In a flush and semi-flush
installation, the finished dimension (width of the
opening after side panels are installed) must
accommodate the full width of the product.
See page 11 for side panel sizes.