Advertisement
Lighting Your Grill by Match
To light your gas grill by match, follow steps 1 through
6 of the Basic Lighting Procedures. Then, insert a lit
match through the Lighting Hole on the left side of the
grill. See Figure 14. Turn the nearest Control Knob to
the HIGH setting to release gas. The Burner should
light immediately.
Figure 14
LIGHTING
HOLE
\
\
\
\
®
Z WARNING
Never lean over the grill cooking area while
lighting your gas grill. Keep your face and
body a safe distance
(at least 18 inches)
from the Lighting Hole or Burners, when
lighting your grill by match.
If the grill fails to light :
1. Turn gas off at source and turn the Control Knob to
OFF. Wait at least five minutes for gas to clear,
then retry.
2. If your grill still fails to light, check gas supply
and connections.
3. Repeat lighting procedure. If your grill still fails
to operate, turn the gas off at source, turn the
Control Knobs to OFF, then check the following:
• Misalignment of BurnerTubesover Orifices
Correction: Reposition BurnerTubesoverOri-
rices.
• Obstruction in gas line
Correction: Remove fuel line from grill. Do not
smoke! Open gas supply for one second to clear
any obstruction from fuel line. Close off gas supply
at source and reconnect fuel line to grill.
• PluggedOririce
Correction: Remove Burners from grill by
loosening screw using screw driver. Carefully lift
each Burner up and away from gas valve Orifice.
Remove the Orifice from gas valve and gently
clear any obstruction with a fine wire. Then
reinstall all Orifices, Burners, Cotter Pins and
cooking components.
If an obstruction is suspected in gas valves or
gas valve bracket, please call for repair service at
1-800-4-MY-HOME _.
4.
.
• Obstruction in BurnerTubes
Correction: Followthe Burner Tube cteaning
procedure on page 21 of this Owner's Manual
• Misalignment of Spark on Burner
Correction: Check for proper position of the
Electrode Tip as shown in Figure 10. The gap
between the Spark Electrode Tip and Spark
Receiver should be approximately
3/16". Adjust
if necessary. With the gas supply closed, push
and turn each Control Knobs to High, check for
the presence of a spark at the Electrode.
If the grill still does not light you may need to
purge air from the gas line or reset the regula-
tor excess gas flow device.
Note: This proce-
dure should be done every time a new LP gas
tank is connected
to your grill.
To purge air from your gas line and/or
reset the regulator
excess gas flow device:
• Turn the Control Knobs to the OFF position.
• Turn off the gas at the tank valve.
• Disconnect
regulator from LP gas tank.
• Let unit stand for 5 minutes to allow air to
purge.
• Reconnect regulator
to the LP gas tank.
• Turn the tank valve on slowly until 1/4 to
1/2 open.
• Open the Grill Lid.
• Push and turn the LEFT Control Knob to
HIGH.
If all checks or corrections have been made and
you still have questions about operating your gas
grill, call
theGrill
Information
Center
8am - 8pm CST, Monday through
Friday at
1-888-317-7642.
Z WARNING
Should a FLASHBACK fire occur in/or
around the Burner Tubes, follow
the
instructions
below. Failure to comply with
these instructions
could result in a fire or
explosion that could cause serious bodily
injury, death, or property damage.
• Shut off gas supply to the gas grill.
• Turn the Control Knobs to OFF position.
• Open the Grill Lid.
• Put out any flame with a Class B fire
extinguisher.
• Once the grill has cooled down, clean the
Burner Tubes and Burners according to
the cleaning
instructions
found on page 21
in this manual.
16
Advertisement
