Bugera Trirec Infinium Amplifier Quick Start Manual page 7

12
BUGERA TRIREC INFINIUM
BUGERA TRIREC INFINIUM Controls
(3) (4) (7)
(1) (2) (5) (6) (8) (9)
(14) (15) (16) (17) (18)
(23)
(22)
bugera-amps.com
(11)
(10) (12)
(19) (20) (21)
13
Quick Start Guide
Step 2: Controls
(13)
bugera-amps.com
POWER switch turns the amp on and off. SEND knob adjusts the output level of the FX LOOP
(1) (17)
SEND jack. It should be set as high as possible without
STANDBY switch mutes the amp's output and
(2)
causing the effects processor to clip.
preserves your tubes.
LEVEL knob adjusts the level of the signal coming in
(18)
VARIPOWER knob adjusts the maximum output power
(3)
through the RETURN jack. Set the output from the
capacity, enabling compression and sustain commonly
effects processor as high as possible and adjust the
associated with power tube saturation to be achieved
LEVEL knob to balance the active FX LOOP signal with
at lower volumes.
the bypassed signal.
REVERB knob adjusts the amount of reverb effect.
(4) EXTERNAL SWITCHING jacks are unbalanced
(19)
Engage the effect with the adjacent REVERB button.
non-latching jacks that allow channel switching,
BOOST, REVERB and FX LOOP selection to be
MASTER knob adjusts the amp's overall
(5)
controlled by an external switching system.
volume output.
FOOTSW(ITCH) input allows connection of the
(20)
BOOST knob adjusts the amount of optional volume
(6)
included FSB106A footswitch.
boost. The BOOST can be engaged with the adjacent
button or via the FSB106A footswitch.
RECTIFIER switch selects between the bold,
(21)
powerful sound of silicon diode rectifiers, the warm,
TREBLE, MID and BASS knobs adjust the high,
(7)
spongy feel of rectifier tubes, or a combination of both.
middle and low frequencies of the channel.
FSB106A footswitches select the channel and on/off
(22)
PRESENCE knob adjusts the high end clarity and
(8)
status of the BOOST, REVERB and FX LOOP. Each switch
sharpness of the channel's tone.
has an LED that lights when active. The switches also
VOLUME knob adjusts the channel volume.
set certain MIDI parameters. See Step 3 for details.
(9)
GAIN knob adjusts the amount of distortion on MIDI IN and MIDI THRU jacks allow the FSB106A
(10) (23)
the channel. functions to be switched by an external MIDI controller.
CH 2 and 3 MODE switches select between CLASSIC,
(11)
VINTAGE and MODERN tone styles. Set the switch
to CLASSIC for blues and classic rock crunch tones.
VINTAGE offers more gain and saturation for hard rock
rhythm and lead work. MODERN pushes the gain into
extreme heavy metal territory.
CHANNEL buttons select which of the 3 channels
(12)
is active.
CH 1 MODE switch selects between the CLEAN setting
(13)
for pristine clean sounds, or DRIVE setting for a highly
dynamic crunch tone.
LINE OUT knob adjusts the level of the OUTPUT jack for
(14)
use with a slave amp.
IMPEDANCE switch selects between 4, 8 and 16 Ohms.
(15)
ASSIGN knob allows the following options:
(16)
•
ON – The FX LOOP is always active
•
CHANNEL – The FX LOOP, REVERB, and BOOST
on/off status are stored for each channel and
recalled each time the channel is selected
•
REMOTE – The FX LOOP is turned on and off
with the FSB106A footswitch or EXTERNAL
SWITCHING jack
•
OFF – The FX LOOP is deactivated