Bugera Trirec Infinium Amplifier Quick Start Manual page 10

18
BUGERA TRIREC INFINIUM
BUGERA TRIREC INFINIUM Getting started
Step 3: Getting started
Make all appropriate audio and power
connections to the TRIREC. Leave the
power for all devices off!
Turn the MASTER knob all the way down.
Leaving the STANDBY switch in the down/
off position, flip the POWER switch up to
turn the amp on.
Turn on any other devices connected to
the amp.
Select the RECTIFIER setting on the back
panel. Silicon diodes have the highest
power output and tightest bass response,
while rectifier valves have a lower output but
produce a touch-response that many guitarists
prefer. A combination of the two can also
be selected.
bugera-amps.com
19
Quick Start Guide
After the POWER switch has been engaged
for at least one minute, flip the STANDBY
switch up.
Turn the MASTER knob up to the 9:00
position to start.
cause feedback.
Select one of the 3 channels using
the CHANNEL buttons or the
FSB106A footswitch.
Turn the VOLUME knob up half way on the
selected channel.
seconds of powering the amp on.
bugera-amps.com
Select the basic tonal character using the Adjust the VARIPOWER knob
channel's MODE switch. counterclockwise to achieve power valve
saturation at lower volume settings. Turn
the VARIPOWER knob fully clockwise when no
power reduction is required. This setting allows the
MASTER volume knob to operate normally and
produce the maximum output.
Adjust the amount of distortion using the
GAIN knob. Depending on EQ and volume
settings, too much gain can
Engage the BOOST function and adjust
the BOOST knob to achieve the desired
amount of volume boost for solo sections
during a performance.
If using effects in the FX LOOP, set the
ASSIGN knob to ON if you want the loop
constantly active, or REMOTE if you want
to control the on/off status with the FSB106A
Adjust the equalization using the TREBLE,
footswitch. The CHANNEL setting allows you to
MID, BASS and PRESENCE knobs.
continually control the loop via footswitch,
but saves the on/off status of the FX LOOP,
BOOST and REVERB (including Decay and Send
Repeat steps 8-12 for the other channels.
levels) for each channel. If you are not using the
Use each channel's VOLUME knob to
FX LOOP, set the ASSIGN knob to OFF.
balance the output levels between them.
Adjust the SEND and LEVEL knobs to
Engage the REVERB function and adjust
achieve an optimal FX LOOP signal level
the amount of desired effect. To reset
going to the processor and returning to
the Reverb to default settings, press the
the amp. Make sure the volume level is consistent
REVERB button within the first few
when turning the FX LOOP on and off.
Rock out and have fun!
MIDI Implementation
CC12 FX LOOP (x00, x01)
CC13 BOOST (x00, x01)
CC75 REVERB DECAY (0-7)
Stored per channel when FX LOOP
ASSIGN is "Channel"
Default DECAY setting is 3
Note: changing DECAY resets
REVERB SEND to 127
CC91 REVERB SEND (continuous, 0-127)
Stored per channel when FX LOOP
ASSIGN is "Channel"
Reset to default REVERB SEND (127)
by pressing REVERB during power up
CC120 MUTE
PGM 001 CH 1
PGM 002 CH 2
PGM 003 CH 3
PGM 011 CH 1 + BOOST off
PGM 012 CH 2 + BOOST off
PGM 013 CH 3 + BOOST off
PGM 021 CH 1 + BOOST on
PGM 022 CH 2 + BOOST on
PGM 023 CH 3 + BOOST on
Default MIDI channel = 1
Hold one of the FSB106A footswitches 1-6
during power up to select the
MIDI channel 01-06 accordingly.