Sony LMD-1541W Operating Instructions Manual page 31

Submenu Setting
F1 BUTTON to F7 Assigns the function to the function
BUTTON buttons of the front panel and turns the
function on or off.
You can assign the function from among
SCAN, ASPECT, BLUE ONLY,
MONO, MARKER, I/P MODE, etc.
Factory setting
• F1 button: BRIGHTNESS
• F2 button: CONTRAST
• F3 button: CHROMA
• F4 button: SCAN
• F5 button: H/V DELAY
• F6 button: VOLUME
• F7 button: I/P MODE
About the function assigned to the
function button
SCAN
Press the button to change the scan size of the picture.
With every press of the button for the 4:3 display, the
picture switches in the sequence NORMAL scan t
OVER scan t NATIVE. With every press of the button
for the 16:9 display, the picture switches in the sequence
NORMAL scan t OVER scan t FULL screen t
NATIVE (see "Scan mode image" on page 32).
ASPECT
Press the button to set the aspect ratio of the picture, 4:3
or 16:9.
Note
LMD-1541W has a 15:9 screen ratio.
When the 16:9 signal is displayed, black bars appear in
the upper and lower positions of the display. This is not
a malfunction (see "Scan mode image" on page 32).
BLUE ONLY
Press the button to eliminate the red and green signals.
Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
"chroma" and "phase" adjustments and observation of
signal noise.
MONO
Press the button to display a monochrome picture. When
the buttons is pressed again, the monitor switches
automatically to color mode.
MARKER
Press the button to display the marker. Set the aspect
marker in the MARKER SETTING menu (see page 27).
H/V DELAY
Press the button to observe the horizontal and vertical
sync signals at the same time.
CLOSED CAP.
Press the button to display the closed caption. Set the
closed caption setting in the CLOSED CAPTION
SETTING menu (see page 33).
WFM/ALM/VS (WFM/ALM/VECTOR)
Press the button to display the WFM/ALM/vectorscope
display. Set the WFM/ALM/vectorscope display setting
in the WFM/ALM/VECTOR SETTING menu (see
page 29).
When LINE SELECT is set to ON and WFM is selected,
each time you press the button, the settings change in the
sequence WFM display activated t Line position
setting t WFM display deactivated. Turn the menu
selection control to move the line for setting the line
position.
When LINE SELECT is set to OFF, the WFM display
switches between activated and deactivated.
ZOOM
Press the button to zoom in the WFM/ALM/vectorscope
display. Set the ZOOM setting in the WFM/ALM/
VECTOR SETTING menu (see page 30).
BRIGHTNESS
Press the button to display the adjustment screen and
adjust the picture brightness. Press again to hide the
adjustment screen. However, the picture brightness
remains adjustable. Turn the menu selection control
right to increase the brightness and turn left to decrease
it.
CONTRAST
Press the button to display the adjustment screen and
adjust the picture contrast. Press again to hide the
adjustment screen. However, the picture contrast
remains adjustable. Turn the menu selection control
right to increase the contrast and turn left to decrease it.
CHROMA
Press the button to display the adjustment screen and
adjust the color intensity. Press again to hide the
adjustment screen. However, the color intensity remains
adjustable. Turn the menu selection control right to
increase the intensity and turn left to decrease it.
VOLUME
Press the button to display the adjustment screen and
adjust the volume. Press again to hide the adjustment
screen. However, the volume remains adjustable. Turn
the menu selection control right to increase the volume
and turn left to decrease it.
I/P MODE
Press the button to set the delay by the picture
processing to the minimum level when interlace signal
is input. The mode switches in the sequence INTER-
FIELD t FIELD MERGE t LINE DOUBLER t
31
Adjustment Using the Menus