Related Manuals for Sony LMD-1530MD
Summary of Contents for Sony LMD-1530MD
-
Page 1: Lcd Monitor
4-162-263-13(2) LCD Monitor Instructions for Use Before operating the unit, please read this manual thoroughly and retain it for future reference. LMD-1530MD © 2009 Sony Corporation... - Page 2 If not, this apparatus may lean or fall over and cause an injury. For the customers in Europe The manufacturer of this product is Sony Corporation, Consult with Sony qualified personnel for mounting 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan. arm, wall or ceiling mount installation.
- Page 3 Safety Approval UL Listed and CSA *Note: Grounding reliability can only be achieved when the 6. Model LMD-1530MD is a monitor intended for use equipment is connected to an equivalent receptacle marked ‘Hospital in a medical environment to display pictures from Only’...
- Page 4 LMD-1530MD. Guidance and manufacturer’s declaration-electromagnetic emissions The LMD-1530MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-1530MD should assure that it is used in such an environment. Emission test Compliance...
- Page 5 Guidance and manufacturer’s declaration - electromagnetic immunity The LMD-1530MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD- 1530MD should assure that it is used in such as environment. IEC 60601 test...
- Page 6 Guidance and manufacturer’s declaration - electromagnetic immunity The LMD-1530MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD- 1530MD should assure that it is used in such as environment. IEC 60601 test...
- Page 7 Recommended separation distances between portable and mobile RF communications equipment and the LMD- 1530MD The LMD-1530MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the LMD-1530MD can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (Transmitters) and the LMD-1530MD as recommended below, according to the maximum output power of the communications equipment.
-
Page 8: Table Of Contents
Table of Contents Precaution .............. 9 On Safety ............9 On Installation ............ 9 About the LCD Panel ......... 9 On Burn-in ............9 On a Long Period of Use ........9 On Cleaning ............. 10 Disposal of the Unit ......... 10 Recommendation to Use more than One Unit ............ -
Page 9: Precaution
• Do not push or scratch the LCD screen. Do not place Precaution a heavy object on the LCD screen. This may cause the screen to lose uniformity. • If the unit is used in a cold place, a residual image may appear on the screen. -
Page 10: On Cleaning
If you have any questions about this unit, contact your On cleaning the monitor authorized Sony dealer. A material that withstands disinfection is used for the medical use LCD monitor. When solvents such as benzene or thinner, or acid, alkaline or abrasive... -
Page 11: Features
When the EXT SYNC button is in the on position, the unit can be operated on the sync signal supplied from an external sync generator. The LMD-1530MD is a 15.3-type LCD monitor that Automatic termination (connector with conforms to medical safety standards. This unit is mark only) suitable for endoscopy or use as a sub-monitor. -
Page 12: Location And Function Of Parts And Controls
Location and Function of Parts and Controls Front Panel MENU VOLUME RGB/ BLUE LINE HDMI COMPONENT SYNC ONLY SCAN ASPECT RESET ENTER qs qa 0 9 8 7 6 4 3 2 a Tally lamp ENTER button Turning this lamp on or off can be done with a Press to confirm a selected item on the menu. -
Page 13: Input Signals And Adjustable/Setting Items
m LINE button n Speaker Press to monitor the signal through the LINE input The audio signal selected by the input select button ( connector. SDI button, RGB/COMPONENT button, HDMI button or LINE button) on the front panel is output. Input Signals and Adjustable/Setting Items Input signal Item... -
Page 14: Rear Panel
OPTION IN connector (D-sub 9-pin, female) Analog RGB signal or component (Y/P ) signal input connectors and their loop-through output Inputs HD/SD-SDI signals when optional Sony BKM- connectors. 341HS is connected. Press the RGB/COMPONENT button to monitor the Press the SDI button to select the signal. -
Page 15: Connecting The Ac Power Cord
AUDIO IN/OUT (phono jack) Connecting the AC When using an analog RGB or a component signal as a video signal, use these jacks for the input/output Power Cord of an audio signal. Connect them to the audio input/ output jacks on equipment such as a VCR. g PARALLEL REMOTE connector (modular Plug the AC power cord into the AC IN socket on connector, 8-pin) -
Page 16: Attaching The Input Adaptor
Attaching the Input Removing the Adaptor Connector Cover Before attaching the input adaptor, disconnect the power When the unit is shipped from the factory, a connector cord. cover is attached to the PARALLEL REMOTE connector. BKM-341HS To use the connector, remove the connector cover as follows. -
Page 17: Selecting The Default Settings
Selecting the Default Settings When you turn on the unit for the first time after purchasing it, select the area where you intend to use this unit from among the options. The default setting values for each area MENU VOLUME RESET ENTER Press the 1 (standby) switch. -
Page 18: Selecting The Menu Language
2 If LATIN AMERICA is selected: Selecting the Menu PAL&PAL-N area Language L A T I N A M E R I C A P A L & P A L - N A R E A Argentina A R G E N T I N A P A R A G U A Y Paraguay U R U G U A Y... -
Page 19: Using The Menu
The setting items (icons) in the selected menu are Using the Menu displayed in yellow. SYSTEM SETTING 1/2 The unit is equipped with an on-screen menu for making R G B / C O M P S E L : xxxxxxx C O M P O N E N T L E V E L : xxxxxxx... -
Page 20: Adjustment Using The Menus
Adjustment Using the SYSTEM SETTING 1/2 R G B / C O M P S E L : Menus C O M P O N E N T L E V E L : xxxxx N T S C S E T U P : S C A N : xxxxxx G A M M A :... -
Page 21: Adjusting And Changing The Settings
REMOTE For the DVI input PARALLEL REMOTE 1PIN STATUS 1/2 2PIN F O R M AT xxxxxxx 3PIN xxxxxxx 4PIN xxxxx C O L O R T E M P xxxx 6PIN 7PIN 8PIN KEY INHIBIT STATUS 2/2 KEY INHIBIT L M D - 1 5 3 0 M D xxxxxxx O P T I O N... -
Page 22: User Control Menu
SYSTEM SETTING menu Submenu Setting The SYSTEM SETTING menu is used for setting the MANUAL If you set the COLOR TEMP to ADJUSTMENT USER setting, the item displayed is system. You can set the display language and so on. changed from black to white, which Items that cannot be adjusted depending on the input means you can adjust the color signal are displayed in black. - Page 23 Submenu Setting Submenu Setting FORMAT DISPLAY Selects the display mode of the SD PIXEL MAPPING Selects SD picture size (pixels) signal format. according to input signal format. • AUTO: The format is displayed • COMPOSITE&Y/C: Set to for about 10 seconds when monitor the signal input the input of the signal starts.
-
Page 24: Scan Mode Image
Scan mode image • NORMAL • OVER • TALLY G Input • EXT SYNC • BLUE ONLY • FULL • SDI If you use the PARALLEL REMOTE function, you need to connect cables. OVER SCAN For more details, see page 26. (5% OVER SCAN) KEY INHIBIT menu... -
Page 25: Troubleshooting
Troubleshooting Specifications Picture performance This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical LCD panel a-Si TFT Active Matrix support. Picture size 15.3 type • The display is colored in green or purple t Select 334 ×... - Page 26 Note Phono jack (1), Loop-through Always verify that the unit is operating properly before External synchronized output connector use. SONY WILL NOT BE LIABLE FOR BNC type (1), Loop-through, with DAMAGES OF ANY KIND INCLUDING, BUT 75 ohms automatic terminal...
- Page 27 Video signal formats The unit is applicable to the following signal formats. Total Active Scanning System Frame rate Aspect ratio Signal standard lines lines format 575/50I (PAL) EBU N10 2:1 interlace 16:9/4:3 (PAL: ITU-R BT.624) 480/60I (NTSC) SMPTE 253M 2:1 interlace 16:9/4:3 (NTSC: SMPTE 170M) 576/50P...
- Page 28 When an optional input adaptor is connected, the unit is applicable to the following signal formats. When BKM-341HS is connected Input System Signal standard 575/50I SMPTE 259M 480/60I SMPTE 259M 1080/24PsF SMPTE 292M 1080/25PsF SMPTE 292M 1080/24P SMPTE 292M 1080/25P SMPTE 292M 1080/30P SMPTE 292M...
-
Page 29: Dimensions
Side Dimensions 75.2 (3) 100 (4) Front 372 (14 96.8 (3 264.4 (10 Bottom 204.3 (8 4-M5 Rear 100 (4) 165.1 (6 216.4 (8 Unit: mm (inches) Mass Approx. 6.2 kg (13 lb 11 oz) Dimensions... - Page 30 Sony Corporation...