Table of Contents
Advertisement
1/3 HP Submersible Sump Pump
with Vertical Float Switch
Item 68476 Specifications
Float Switch Operation Height
Electrical Requirements
Power Cord Length
Maximum Capacity
Maximum Delivery Height
Discharge Size
Maximum Water Temperature
Read the separate Sump Pump Safety Warnings,
Installation and Operation Instructions before
using this product.
Failure to do so can result in serious injury.
SAVE THIS SPECIFICATION SHEET AND
THE SUMP PUMP SAFETY WARNINGS,
INSTALLATION AND OPERATION
INSTRUCTIONS FOR FUTURE REFERENCE.
When unpacking, make sure that the product is intact and undamaged.
If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.
©
Copyright
2011 by Harbor Freight Tools
or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
7.1 IN. ON / 2.8 IN. OFF
120V~ / 60Hz / 7.6A
10 FT.
3000 GPH
25 FT.
1.5 IN. NPT
(includes 1.25 IN. Adaptor)
77° F (25°C)
252728
Visit our website at: http://www.harborfreight.com
®
. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape
Advertisement
Table of Contents
Related Manuals for Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float Switch
Summary of Contents for Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float Switch
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing...
-
Page 2: Parts List And Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. - Page 3 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing...
-
Page 4: Power Supply
reproductive harm. Wash hands after handling. Before start-up, note the following: (California Health & Safety Code § 25249.5, et seq.) The pump can be connected to any shock-proof plug 14. The warnings, precautions, and instructions which has been installed according to regulations. discussed in this instruction manual cannot The plug must have a supply voltage of 120 V~ at 60 Hz. -
Page 5: Areas Of Use
3. Fit a sump cover with a hole for the output pipe WARNING! If either power cord or plug is damaged, and power cords. Thread the Power Cords do not use the pump. The power cord or plug through their holes, but do not plug them in yet. may only be repaired by a certified electrician. -
Page 6: Operation
10. After connecting power to the pump and Operation periodically afterwards, test the pump: a. Fill the basin to above the Float Switch Operation After reading these instructions, ON Height. The pump should start pumping. consider the following points before starting the pump: b. -
Page 7: Quarterly Maintenance
Cold Weather Storage Maintenance In cold weather, when the Pump is not in use, protect the interior of the Pump from freezing by draining the water and pumping a permanent type automobile anti-freeze containing a rust inhibitor TO PREVENT SERIOUS INJURY FROM through the system. -
Page 8: Troubleshooting
Troubleshooting Problem Possible Causes Possible Solutions Pump runs, but Disconnect power cords immediately Disconnect power cords immediately will not deliver to prevent damage from running dry. to prevent damage from running dry. any water. 1. Pump “airlock”. 1. Drill a 3/16 IN. diameter air bleed hole Impeller trapped in an air bubble. -
Page 9: Limited 90-Day Warranty
Proof of purchase date and an explanation of the complaint must accompany the merchandise. If Harbor Freight Tools Co. makes every effort to assure our inspection verifies the defect, we will either repair that its products meet high quality and durability...