Disarming By Emergency Override - Crime Guard 328i4 Operation Manual

second period, if no protected entry points are opened and the vehicle's
ignition is NOT turned on, the system will automatically arm itself at the end
of the countdown. If desired, the system can also be programmed to
automatically relock the doors when this occurs.
Automatic Rearming Notes
Turning the vehicle's ignition on cancels Automatic Rearming.
•
Opening a door will suspend the 90 second countdown.
•
All protected zones must remain non-violated during the 90 second
•
Automatic Rearming period. For example, if a vehicle door is opened
during the 90 second period, the countdown will stop. When the door is
closed, the system resets and starts a new 90 second countdown.
The Automatic Rearming sequence is indicated by a fast flashing Status
•
Light, unless the system has been activated, in which case a Zone Violation
code will flash instead (page 15). The ignition switch must be turned on
to erase a Zone Violation code.
If the system is disarmed while it is activated (siren sounding and lights
•
flashing) Safety Disarm will cancel the Automatic Rearming for that
disarming operation only. The next time the system is armed, Automatic
Rearming will be initiated upon the subsequent disarming.

DISARMING BY EMERGENCY OVERRIDE

Emergency Override:
In the event that your transmitter is lost, damaged, or its batteries have
become exhausted, the Valet Switch and the vehicle's ignition key may be
used to disarm the system. How the Valet Switch is used for this operation
may also be customized; this is the SecureCode feature, the operation of
which is described on page 22.
The following Emergency Override instructions reflect the SecureCode
entry of the Valet Switch as the "as received" default setting of "1 press".
To Disarm the System without using a Transmitter:
Step 1 With the system in the armed condition, enter the vehicle via the
driver's door (be aware that the system will activate to an alarm
condition when the door is opened).
Step 2 Using the ignition key, turn the vehicle's ignition on.
Step 3 Within 5 seconds, enter the SecureCode by pressing and releasing
the Valet Switch once. The system will disarm.
Page 10
to chirp the total number entered Valet switch entry.
Important: Now let the system exit Programming Mode by allowing the 10
second time limit to expire without any further programming activity. Do not exit
Programming Mode by turning on the ignition switch.
Feature #2 30 or 60 Second Alarm Duration:
This feature allows the choice of a 30 or 60 second Alarm Duration, which is the
system triggering, or activating, sounding the siren, flashing the parking lights and
locking the doors. When programming, pressing the transmitter's Upper Left "Lock"
Button will select the 60 second setting; pressing the Upper Right "Unlock" Button
will configure the 30 second setting.
Feature #3 3 / 45 Second Arming Delay:
When the system is armed, either by the transmitter or automatically, there is a brief
period of time in which a system activation cannot occur. This allows the system to
completely process the arming operations, and the vehicle to stabilize. In some cases
more time is needed than the factory-set 3 seconds. This feature offers a longer 45
second delay.
When programming, press the transmitter's Upper Left "Lock" Button will select
the 3 second Arming Delay; pressing the Upper Right "Unlock" Button will
configure the 45 second setting.
Feature #4 Last Door Arming
"Last Door Arming" has the system automatically arm itself every time you exit the
vehicle (the complete operation is described on page 6). This feature turns that
operation on or off. When programming, press the transmitter Upper Left "Lock"
Button to turn on Last Door Arming; or press the Upper Right "Unlock" Button to
turn it off.
Feature #5 Automatic Rearming
"Automatic Rearming", described on page 9, prevents the system from becoming
accidentally disarmed. When programming, press the transmitter Upper Left "Lock"
Button to turn this feature on, or press the Upper Right "Unlock" Button to turn it off.
Feature #6 Auxiliary Channel #2 Also Disarms System
"Auxiliary Channel #2" is most commonly used to remotely open the trunk, in which
Page 23
(Factory Default
Setting 30 Seconds)
(Factory Default Setting
3 Second)
(Factory Default Setting Off)
(Factory Default Setting Off)
(Factory Default Setting On)