GE AJCH 08 ACB Owner's Manual And Installation Instructions page 5

wnnN.GEAppliances.com
COOLMODE
Remote C ontrol
l. Px_ss COOL pad.
2. P*_ss LOW.MEDor HIpads to set desired fire
speed.
3. Px_ss die INCREASEA/DECREASET padsto
set
the
desix_d temperature
60°F to 85°F ill l °F increments.
Control Panel
l. Pless die MODEpad until tile COOLindicator lig]lt is
lit and the LOW. MEDor Hlin(ficator light is lit for
dm desil_d t_m speed.
2. Pl_ss the INCREASE&/DECREASET pads to set the
desil_d temperature 60°F to 85°F ill l °F increments.
A them/osmt is used to maintain tile roon/
tempenmlre.
Tile con/pressor will (3cle on and off
to keep tile room at tile set level of comfi)rt. Set file
thermostat at a lo_r number and tim indoor air will
become coolel; Set tile thermostat at a higJmr nm-nber
and tile indoor air will become _mnel:
NOTE:ff the air conditioner is off andis then turned on
while set to COOL, i t will take approximately3 minutes for
the compressor to start and cooling to begin.
CoolingDescriptions
ForNormalCooling--Select the COOL mode and
HIGHor MEDtim with a middle set temperature.
ForMaximum Cooling--Select tile COOL mode
and HIGHfire with a lower set temperaU/l>.
ForQuieter& NighttimeCoolino--Select tile COOL mode
and LOWfimwifl_a middle set temperature.
NOTE: If youswitchfroma COOL s ettingtoOFF or to
a fansetting,wait atleast3 minutes beforeswitchingback
toa COOL s etting.
Fan Switch
Tile tim switch is located behind tile ti'ont grille on the
control box. Access through a hole ill control box.
_A]mn set at CYCLE ((]o_n) tile thn e_cles on and oti_
When set at
CONT (continuous, up)
tile tim runs all tile
time providing a mol_ balanced mmperaull_. The unit
is shipped ill the
cONrsetting.
FAN MODE
Use tile FANmode to pro\ide _dr circulation and
filtering without cooling. Since fire only settings do not
provide cooling, a temt)emture setting will not be
displa}ed.
Remote Control
Pl>ss FANpad. Press LOW,MED or HI pads to set
desil_d Jim speed.
Control Panel
Pless die MODEpad until tile FANindicator light is lit
and tile LOW, MEOor HIin(ficator light is lit fi)r the
desil>d Jim speed.
Vent Control
Tile vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_lmn set at
CLOSE,
only tile air inside file room will be circulated
and conditioned. When set at OPEN, some inside air is
exhausted outside.
To opell or
close
tile vent:
1. Remove the ti'ont grille.
2. Remove tile vent card scions.
3. Remove vent card, turn it o\'er and replace it b}
locating rear hole ill card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunit leavesthe factoryset at theCLOSE position.
._Locating hole
Screw hole "_.
OPEN position
(Meshendtowardback)
Screwho
CLOSE position
(Meshendtowardfront)
A# Direction
Horiz(mt_fl lomers
(m tim front grille let
you control tile _dr
(lirecti(m up and
doPvI/.
Remo\'e tile fl'ont
,grille to a(!just file
vertical louvers
side-to_ide to
dilect the air
left or fight.