Kenmore 106.5478 Use & Care Manual page 28

Base Grille Water Filtration System
Model PIKB1/PIRFKB1 Capacity 100 Gallons (379 Liters)
System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of
Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of
Lead, Mercury, Atrazine, Benzene, Toxaphene, O-Dichlorobenzene, Cysts, Turbidity, Asbestos, Lindane,
Tetrachloroethylene, Endrin, Alachlor, Styrene, Chlorobenzene, Ethylbenzene, TTHM, MTBE and VOC.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system_ as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Minimum % Average %
Aesthetic Effects Requirements Influent Concentration Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 2.10 mg/L 2.0 mg/L + 10% 0.05 mg/L 97.6 97.6
Particulate Class I* 85% reduction 21000000#/mL At least 10,000 particles/mL 140000 #/mL** 99 99.5
Contaminant NSF Reduction Average Influent Challenge Maximum Minimum % Average %
Reduction Requirements Influent Concentration Effluent Reduction Reduction
Lead: @ pH 6.5 0.010 mg/L 150 ug/L 0.15 mg/L + 10% 1.0 ug/L 99.3 99.3
Lead: @ pH 8.5 0.010 mg/L 160 ug/L 0.15 mg/L _+10% 2.0 ug/L 99.4 99.3
Mercury: @ pH 6.5 0.002 mg/L 5.8 ug/L 0.006 mg/L + 10% 0.2 ug/L 96.6 96.6
Mercury: @ pH 8.5 0.002 mg/L 6.1 ug/L 0.006 mg/L _+10% 0.4 ug/L 93.4 95.3
Benzene 0.005 mg/L 15 ug/L 0.015 mg/L _+10% 0.5 ug/L 96.7 96.7
O-Dichlorobenzene 0.6 mg/L 1900 ug/L 1.8 mg/L _+10% 0.7 ug/L 99.9 99.9
Toxaphene 0.003 mg/L 14 ug/L 0.015 mg/L _+10% 1.0 ug/L 91.5 92.8
Atrazine 0.003 mg/L 9.0 ug/L 0.009 mg/L _+10% 0.5 ug/L 94.5 94.5
Asbestos 99% 130 M FL 107to 108fibers/L tt 0.17 M FL 99 99
Live Cysts _ >99.95% 96,000/L 50,000/L min. 1/U 99.99 99.99
Turbidity 0.5 NTU 12 NTU 11 _+1 NTU 0.4 NTU 96.7 98.5
Alachlor 0.002 mg/L 41 ug/L 0.04 mg/L _+10% 1.0 ug/L 97.6 97.6
Endrin 0.002 mg/L 5.9 ug/L 0.006 mg/L _+10% 0.2 ug/L 96.5 96.6
Ethylbenzene 0.7 mg/L 2100 ug/L 2.1 mg/L _+10% 0.5 ug/L 99.9 99.9
Lindane 0.0002 mg/L 1.9 ug/L 0.002 mg/L _+10% 0.02 ug/L 99 99
Chlorobenzene 0.1 mg/L 2100 ug/L 2.0 mg/L _+10% 1.1 ug/L 99.9 99.9
Tetrachloroethylene 0.005 mg/L 14 ug/L 0.015 mg/L _+10% 0.5 ug/L 96 96.4
Styrene 0.1 mg/L 2200 ug/L 2.0 mg/L _+10% ND (0.5) 99.9 99.9
TTHM 0.080 mg/L 480 ug/L 0.45 _+20% 3.9 ug/L 99.2 99.8
MTBE 0.005 mg/L 15 ug/L 0.015 _+ 20% 1.3 ug/L 91.3 96.2
V©C 0.05 mg/L 300 ug/L 300 _+30 ug/L ND (0.5) 99.8 99.8
Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure =
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 100 gallons (379 liters).
• It is essential that operational, maintenance, and filter •
replacement requirements be carried out for the product to
perform as advertised.
• Model PIKBI" The filter monitor system measures the amount of
water that passes through the filter and alerts you to replace the •
filter.
Style 1 - When the filter indicator reads 10%, order a new filter. •
When the indicator reads 0%, it is recommended that you
replace the filter.
Style 2 - When the filter indicator changes from green to yellow,
order a new filter. When the indicator changes from yellow to red,
it is recommended that you replace the filter.
Style 3 - When the water filter status display changes from
"GOOD" to "ORDER," order a new filter. When the filter indicator
reads "REPLACE," it is recommended that you replace the filter.
Use replacement cartridge P1 RFKB1, part #9030.
2008 suggested retail price of $59.99 U.S.A./S71.99 Canada.
Prices are subject to change without notice.
• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
• The product is for cold water use only.
60 psig (413.7 kPa).
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.
Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 L/min) @ 60 psi
*Class I particle size: >0.5 to <1 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
ttFibers greater than 10 um in length
_Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.
28