Advertisement
System Configurations
Basic Configurations
Wind Transducer
Wind Transducer
Wind
Digital
Digital
Wind
12 V
12 V
Depth/Speed/Temp
Depth/Speed/Temp
Sensor
Sensor
Sail Boat
Navnet 3D
WAAS/GPS
Multi Function
Network Radar Sensor
Antenna
Display
Wind Transducer
Digital
Wind
Multi
Junction Box
Depth/Speed/Temp
* 12V power will be supplied from NavNet 3D
Sensor
Power Boat
Navnet 3D
WAAS/GPS
Multi Function
Network Radar Sensor
Wind Transducer
Antenna
Display
Digital
Wind
Multi
HUB
Junction Box
Depth/Speed/Temp
Sensor
DFF1
Transducer
* 12V power will be supplied from NavNet 3D
WIND
CH WIND
FI-501
FI-502
Apparent and True Wind Angle is displayed
The FI-502 provides detailed and precise
in both analog and digital format when
wind bearing measurements from 60 port to
connected to the FI-5001 or other
60 Starboard, an important range for Close
NMEA2000
®
wind measurement system.
Hauled (CH) points of sail.
Multi
Data displayed
12 V
•Apparent and true wind speed •Apparent and true wind angle •Maximum true wind speed
•MAX/LOW true wind speed alarm •High/Low apparent wind angle alarm •Beaufort wind speed
•VMG to windward
CH Wind
NMEA 2000
®
NMEA 0183
Ethernet
others
DIGITAL
MULTI
FI-503
FI-504
The FI-503 displays critical digital data for
The FI-504 features a large digital display.
The FI-505 provides a digital compass
navigation, such as depth, speed, temp, and
The combination of alpha and numeric
readout with an analog "Off-Course"
atmospheric weather data in a 3-way split
characters present all of the data and
needle that greatly assists the helmsman
screen.
functionality available in the FI-50 Network.
in maintaining the desired vessel course.
Alternating Data Displays are possible and
Or, use the needle to check and verify the
Data displayed
selected information can be switched at 3
autopilot steering performance.
second intervals.
1
•Current depth •Shallow/deep alarm
Data displayed
•Shallow/deep anchor alarm •Wind angle
•High/Low apparent wind angle
Data displayed
•Current heading •Locked heading
•Displays all information on the FI-50 series
•Average heading •Course over ground
2
•Boat speed •MAX/AVG STW •SOG •MAX/AVG
•NAVIGATION (Bearing/distance to WPT, XTE, WPT
SOG •VMG to windward •Wind speed •MAX
number/name, L/L, Satellites tracked, Roll & Pitch)
true wind •MAX/LOW true wind speed alarm
•ENVIRONMENT (Battery voltage, Time & Date)
•Beaufort wind speed
•ENGINE (Trip fuel used, Fuel consumption,
3
•LOG •Trip •Count up/down timer •Water
Engine RPM)
temperature •Air temperature •Air pressure
Specifications of FI-50 series
•Humidity •Wind chill temperature •Dew point
Display:
Power supply:
Temperature:
Waterproofing: IP56
Sensors and Accessories (Option)
COURSE PILOT
RUDDER
Easy to install
Surface Mount the displays with a hole saw then install 4 hidden
screws under the front bezel. Installations are easy and clean with
FI-505
FI-506
a finished appearance (1"(26mm)bulkhead protrusion)
Connected to an Autopilot, the FI-506
Rudder Angle Display show precise rudder
angle information.
Data displayed
•Rudder angle
Surface mount installation
The units are designed to match the
NavNet 3D series and other navigation
equipment. The "Plug and Play" system
Analog and digital LCD (FI-501, 502, 505)
utilizes NMEA 2000
®
Digital LCD (FI-503, 504)
which gives the system exceptional
Analog (FI-506)
interface ability.
12 VDC, less than 0.1 A
–15°C to +55°C
Easy to Read with Silver Bright LCD Display
Wind Transducer
FI-5001
Angle Accuracy:
Better than ±10°
The FI-50 Series utilize high-contrast, backlit LCD displays for
Speed Accuracy:
Better than ±5 % (20 kt)
superior viewing even in direct sunlight. Each unit features an
Power supply:
12 VDC, less than 40 mA
easy-to-read display and 4 simple programming buttons for
Transducer cable:
30/50 m
operation. The function for each key and combination is printed
directly on the front panel.
Depth/Speed/Temp Sensor
FI-503 DIGITAL
DST-800
Frequency:
235 kHz
22 mm
22 mm
Junction Box
FI-5002
NMEA2000
®
backbone x 2 ports
®
NMEA2000
x 6 ports
Power supply:
12 VDC, less than 2 A
Operational guide description on the front panel
Optional "Low Profile" Flush Mounting front panels provide
a cosmetic match to NN3D Displays and a custom console
appearance (0.4"(10mm)bulkhead protrusion)
Flush mount installation
with optional front panel
Wind Transducer
interface protocol,
FI-501
FI-503
MULTI FUNCTION
DISPLAY
JUNCTION
BOX
Automatic Backlight Adjustment
The FI-50 series of instruments minimize power consumption
by turning off the backlight during the daytime. Sensors on
the front panel measure ambient lighting conditions and
adjust the on/off condition of the display backlighting
accordingly.
FI-504 MULTI
Daytime
Sunset or after
41 mm
Back Light
Turns On
Automatic Detection
Back Light
Turns Off
Advertisement
