Hide thumbs Also See for B-SV4D Series:

Advertisement

TOSHIBA Barcode Printer
B-SV4D SERIES
Owner's Manual
Mode d'emploi
Bedienungsanleitung
Manual de instrucciones
Gebruikershandleiding
Manuale Utente
Manual do Utilizador

Advertisement

Table of Contents
loading

Summary of Contents for Toshiba B-SV4D Series

  • Page 1 TOSHIBA Barcode Printer B-SV4D SERIES Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Manuale Utente Manual do Utilizador...
  • Page 2 “Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.” (for CANADA only) The EA10953 AC adapter should be exclusively used for the B-SV4D Series printer. The B-SV4D Series printer must be powered by the EA10953 AC adapter. Waste Recycling information for users:...
  • Page 3 TOSHIBA Barcode Printer B-SV4D SERIES Owner’s Manual...
  • Page 4: Safety Summary

    Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off the power, unplug the machine, then contact your authorised TOSHIBA TEC representative for assistance. Meanings of Each Symbol This symbol indicates warning items (including cautions).
  • Page 5 • Utilize our maintenance services. After purchasing the machine, contact your authorised TOSHIBA TEC representative for assistance once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.
  • Page 6: Table Of Contents

    INDEX CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. 3. Please refer to your local Authorized Service representative with regard to any queries you may have in...
  • Page 7: Product Overview

    ENGLISH VERSION EO1-33061 1.1 Introduction 1. PRODUCT OVERVIEW Thank you for choosing the TOSHIBA B-SV4D series barcode printer. 1.1 Introduction This Owner’s Manual contains valuable information from general set-up to confirming the printer's operation using test prints. You should read it carefully to help you gain maximum performance and life from your printer.
  • Page 8 1.4 Accessories When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your Authorised TOSHIBA TEC representative. (As of September 2004) Certification Certification...
  • Page 9: Appearance

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33061 1.5 Appearance The names of the parts or units introduced in this section are used in the 1.5 Appearance following chapters. 1.5.1 Dimensions 260.8 (10.3) 200 (7.9) 231.8 (9.1) NOTE: The picture on the right is the GC model’s.
  • Page 10: Interior

    1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33061 1.5 Appearance 1.5.4 Interior WARNING! Print Head Do not touch the print head or around it just after printing. Cover Open You may get burned as the Sensor print head becomes very hot during printing. Caution Symbol for the Print Head (Please refer to WARNING!)
  • Page 11: Printer Setup

    • For best results, and longer printer life, use only TOSHIBA TEC recommended media. • Store the media in accordance with the specifications.
  • Page 12: Procedure Before Operation

    The printer can also be controlled ROM.) with its own programming commands. For details, please contact your TOSHIBA TEC reseller. When the printer is connected to a host computer it is good practice to 2.3 Turning the Printer turn the printer ON before turning on the host computer and to turn OFF ON/OFF the host computer before turning off the printer.
  • Page 13: Turning Off The Printer

    2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.4 Connecting the Cables to the Printer 1. Before turning off the printer power switch verify that the Indicator 2.3.2 Turning OFF the Lamp is illuminated in green, not flashing. Printer 2. To turn OFF the printer power press the power switch as shown in the diagram below.
  • Page 14: Connecting The Power Adapter And The Power Cord

    1-2. 2. The EA10953 AC adapter should be exclusively used for the B-SV4D Series printer. The B-SV4D Series printer 3. Insert the Power Adapter connector into the Power Jack on the rear of must be powered by the the printer.
  • Page 15: Loading The Media

    2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media 2.6 Loading the Media This section describes in detail how to load the media. 1. Turn OFF the printer and open the Top Cover. 2. When the inner core diameter of the media roll is 25.4 mm (1”), WARNING! remove the Media Holder Spacers from the Media Holders.
  • Page 16 2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media 6. Feed the media between the Media Guides. 2.6 Loading the Media 7. Pull the media until it extends past the Media Outlet. (Cont.) 8. Adjust the Media Guide position to the media width by rotating the Media Guide Adjustment Knob.
  • Page 17 2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media Strip mode (Option): 2.6 Loading the Media (Cont.) When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed. • How to set the media When issuing labels in the strip mode, set the label in the following procedure: 1.
  • Page 18 2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media When a media roll has an outside diameter exceeding 127 mm (5”) or an 2.6 Loading the Media inner core diameter of 38.1 mm (1.5”), the optional External Media Roll (Cont.) Hanger will be required.
  • Page 19: Media Sensor Calibration, Self Print Test, And Dump Mode Utilities

    2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities This utility is used to calibrate the sensitivity of the Feed Gap/Black 2.7 Media Sensor Mark Sensor. Calibration, Self Print It is necessary to set the media sensors after the media is changed to different type.
  • Page 20 2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities Print test label sample 2.7.2 Self Print Test and Dump Mode (Cont.) PRINTER INFO. PROGRAM VERSION VX.XX XXXX NOTE: TONE ADJUST The following commands should FEED ADJUST +XX.Xmm not affect the test print issue.
  • Page 21 2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities INFORMATION: ------------------------------- Printed only when some information is 2.7.2 Self Print Test and stored in the flash ROM Dump Mode (Cont.) TOTAL FEED----------------------------------- Total feed distance IP ADDRESS ------------------------------------ IP address SUBNET MASK -------------------------------- Subnet mask GATEWAY-------------------------------------- Gateway...
  • Page 22: Maintenance

    3. Do not touch the print head element with bare hands, as static may damage the print head. NOTE: Please purchase the Print Head Print Head Cleaner Cleaner from the authorized (Part No.: 24089500013) TOSHIBA TEC service representative. E3- 1...
  • Page 23: Platen/Sensors

    3. MAINTENANCE ENGLISH VERSION EO1-33061 3.1 Cleaning 1. Wipe the Platen with a soft cloth moistened with alcohol. 3.1.2 Platen/Sensors 2. Remove dust or paper particles from the Media Sensor and Cover Open Sensor using an air blower. Cover Open Sensor Media Sensor Platen...
  • Page 24: Care/Handling Of The Media

    3. MAINTENANCE ENGLISH VERSION EO1-33061 3.2 Care/Handling of the Media • Do not store media for longer than the manufacturer’s recommended 3.2 Care/Handling of the shelf life Media • Store media rolls on the flat end. Do not store them on the curved CAUTION! sides as this might flatten that side causing erratic media advance and poor print quality.
  • Page 25: Troubleshooting

    WARNING! If a problem cannot be solved by taking actions described in this chapter, do not attempt to repair the printer. Turn off and unplug the printer. Then contact an authorised TOSHIBA TEC service representative for assistance. 4.1 Troubleshooting Guide...
  • Page 26: Appendix 1 Specifications

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33061 A1.1 Printer APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use on the B-SV4D printer. A1.1 Printer The following are the printer specifications. Item Specifications Supply voltage AC100 to 240V, 50/60 Hz...
  • Page 27: A1.2 Options

    The above options are available from your nearest TOSHIBA TEC representative or TOSHIBA TEC Head Quarters. A1.3 Media Please make sure that the media to be used is approved by TOSHIBA TEC. The warranties do not apply to problems caused by using media that is not approved by TOSHIBA TEC.
  • Page 28: A1.3.2 Detection Area Of The Transmissive Sensor

    25.4, 38.1, or 76.2 (1, 1.5, or 3) NOTES: 1. To ensure print quality and print head life use only TOSHIBA TEC approved media. 2. When using a media roll of 76.2-mm (3”) inner core diameter, the 3”-Diameter Media Shaft included in the optional External Media Roll Hanger is required.
  • Page 29: A1.3.4 Effective Print Area

    APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33061 A1.3 Media A1.3.4 Effective Print Area The figure below illustrates the relation between the head effective print width and media width. Out of print range Out of print range Print head element 108.0 mm±0.2mm (Head Effective Print Range) 2 mm 2 mm...
  • Page 30: Appendix 2 Interface

    APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33061 APPENDIX 2 INTERFACE APPENDIX 2 INTERFACE Interface Cables To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: • Fully shielded and fitted with metal or metallized connector housings. •...
  • Page 31 GLOSSARIES ENGLISH VERSION EO1-33061 GLOSSARIES GLOSSARIES Bar code Label A code which represents alphanumeric characters A type of media with adhesive backing supplied on by using a series of black and white stripes in a backing paper. different widths. Bar codes are used in various industrial fields: Manufacturing,...
  • Page 32: Index

    INDEX ENGLISH VERSION EO1-33061 INDEX INDEX Backing paper A1-3 Keyboard display unit A1-2 Bar code A1-1 Batch mode 2-6 Black mark A1-2 Label A1-2 Black mark length A1-3 Label length A1-3 Black mark sensor 2-6, 2-9 Label pitch A1-3 Label width A1-3 LAN 1-1, 1-3, 2-3, A1-1 Centronics 1-4, 2-2, 2-3, A1-1 LAN adapter A1-2...
  • Page 33 INDEX ENGLISH VERSION EO1-33061 INDEX Serial interface 1-3, 2-3, A1-1, A2-1 Strip mode 2-7 Supply voltage A1-1 Tag paper A1-2 Thermal direct A1-1 3”-diameter media shaft 2-8 Two-dimensional code A1-1 USB interface 2-3, A1-1 Weight A1-1...
  • Page 34 EO1-33061A...

Table of Contents